manualshive.com logo in svg

SOMFY animeo DRM, Instructions Manual

Share
Download
SOMFY animeo DRM Instructions Manual Download Page 38

 animeo KNX 4 AC MoCo · REF. 5071074 - 

38/47

6.10  Menu index card "Radio binary input 1...5"

"Radio binary input 1...5"

Basic function

Selection options: 

 

Venetian blind UP / DOWN

 

  Switch/Dry contact

 

  8-Bit value (rising edge)

 

  Dimming

 

  Venetian blind turn slowly

Long operation move after

Selection options: 

 

0.5 seconds

 

  0.3...5.0 seconds

This parameter defines the activity time of the corresponding transmitter push button which distinguishes between the sending of a 

short-term telegram (Step/Stop) and a long-term telegram (UP/ DOWN). If the time, for example, is parametered on 0.5 seconds, then only 

after a pressing of more than 0.5 seconds is a long-term telegram generated. With a pressing of the push button which is shorter than 0.5 

seconds, a short-term telegram is generated.

Functionality of the "my" push button

Selection options: 

  1-Bit value

 

  8-Bit value

 

 

No function (no evaluation)

Functionality of the "my" push button

1-Bit value 

Selection options: 

 

On

 

  Off

 

  Toggle

 

  No function

  On

If the "my" button in the radio transmitter is pressed, the object value "On" is generated. The duration of the activity is not evaluated.

On ("1")  Off ("0") 

Toggle ("1/0")

Summary of Contents for animeo DRM
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands