manualshive.com logo in svg

SOMFY animeo DRM, Instructions Manual

Share
Download
SOMFY animeo DRM Instructions Manual Download Page 2

 animeo KNX 4 AC MoCo · REF. 5071074 - 

2/47

Before starting up it is necessary to follow the safety instructions in this instruction. SOMFY cannot be held liable for de-

fects and damages when these have been caused as a result of not following instructions (wrong installation, incorrect 

service etc.). Establishing, testing and starting up of the equipment is permitted only by a qualified person (in accord-

ance with VDE 0100). Switch on all connections without voltage. Take precautions against unintentional turning on.

 The installation of the Somfy products may occur only at easily accessible places. If maintenance and repair become 

hindered by accessibility substantially (e.g. stuck or extensively stuck flooring, installation behind lamps or behind 

façades), any originating supplementary costs therein cannot be charged to the seller.

These instructions apply to KNX 4 AC Motor Controller WM/DRM 220 - 240 V AC from version B onwards!!!

 

Table of Contents

 

Introduction

 

 .....................................................................................................

  3

1

 

Definitions 

 ......................................................................................................

  4

2

 

Installation 

 ......................................................................................................

  5

3

 

Wiring diagram 

 ..................................................................................................

  5

 

3.1  Checking the move direction of the end products 

 ............................................................   

6

4

 

Settings in the delivery state 

 ....................................................................................

  7

 

4.1  Function of the Reset/Prog button 

 ..........................................................................   

7

 

4.2  Selection of different user ergonomics 

 ......................................................................   

7

 

4.3  Manual learning-in of move and turn times

  ................................................................   

8

 

4.4  Manual learning-in of the intermediate position 1

  .........................................................   

8

 

4.5  Resetting to the delivery state

  ..............................................................................   

9

5

 

Communication objects 

........................................................................................

  10

6

  Parameters 

 ....................................................................................................

  17

 

6.1  Menu index card "General" 

 ...............................................................................   

17

 

6.2  Menu index card "Motor 1 ... 4" 

 ..........................................................................   

20

 

6.3  Menu index card "Functions Motor 1 ... 4" 

 .................................................................   

23

 

6.4  Menu index card "Push button binary input 1 ... 4" 

 ........................................................   

25

 

6.5  Menu index card "General: Push button binary input 1-4" 

 ................................................   

32

 

6.6  Menu index card "Electronic Motors" 

 ......................................................................   

33

 

6.7  Menu index card "Bus safety" 

 .............................................................................   

34

 

6.8  Menu index card "Feedback motor positions"

 ..............................................................   

35

 

6.9  Menu index card "General: Radio binary input" 

 ...........................................................   

37

 

6.10  Menu index card "General: Radio binary input 1 ... 5" 

 .....................................................   

38

7

  Diagnosis 

 ......................................................................................................

  44

 

7.1  LEDs on the animeo KNX Motor Controller 

 ..................................................................   

44

 

7.2  Information during operation 

 .............................................................................   

44

 

7.3  Status of the configuration 

 ................................................................................   

44

8

  Push button configuration of the radio transmitters 

 ..........................................................

  45

9

  Technical data 

 .................................................................................................

  46

Summary of Contents for animeo DRM
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands