manualshive.com logo in svg

SOMFY animeo DRM, Instructions Manual

Share
Download
SOMFY animeo DRM Instructions Manual Download Page 34

 animeo KNX 4 AC MoCo · REF. 5071074 - 

34/47

6.7  Menu index card "Bus safety"

"Bus safety"

On this menu index card, the reaction can be defined for every single motor output with bus power failure and bus power return.

MOTOR 1 ... 4 

Reaction at bus power failure

Selection options: 

  Upper end limit

 

 

  Lower end limit 

 

  Ignore 

 

  Intermediate position 1 (IP 1) 

 

  Intermediate position 2 (IP 2) 

 

  Close window 

 

  Open window

MOTOR 1 ... 4 

Reaction at bus power return

Selection options: 

  Upper end limit

 

 

  Lower end limit 

 

  Ignore 

 

  Intermediate position 1 

 

  Intermediate position 2 

 

  Window close 

 

  Window open 

 

  Ignore

MOTOR 1 ... 4 

Reaction at mains power return (230 V)

Selection options: 

  Upper end limit

 

 

  Lower end limit 

 

  Ignore return 

 

  Close window 

 

  Open window

This parameter defines the position which is 

moved to with a bus power failure.

This parameter defines the position which is 

moved to with a bus power return.

This parameter defines the position which is moved to 

with a mains power return (230 V).

Summary of Contents for animeo DRM
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands