SOMFY animeo DRM Instructions Manual Download Page 3

Page: 3 / 47

animeo KNX 4 AC MoCo · REF. 5071074 -

3/47

The animeo KNX Motor Controller WM/DRM 220 - 240 V AC is suited for selecting from up to four individually parameterable motors for Venetian
blinds, roller shutters, awnings and windows. The local push button inputs can be used as conventional push buttons or as universal KNX binary
inputs.

Functions and advantages

• Time savings through easy installation, for example, using spring connectors, strain relief cable binders, sufficient enough clamping space …

• A group input can be used to control all four motors independent of ETS programming.

• Every motor is safe with an individual fuse (3.15, A).

• Moving direction of the motors is possible without ETS.

• The device can be used in the delivery state without programming with the ETS software.

• 4 local push button inputs can be used as maximum 8 universal KNX binary inputs to connect, for example, window contacts, temperature

sensors or presence detectors. Using conventional push buttons, lighting can also be controlled and dimmed.

• User-friendly and intuitive parameter settings in the ETS software.

• Intelligent change-over between manual operation and automatic operation to guarantee excellent user friendliness and energy savings.

• Position messaging of the motors during the movement and when reaching the upper or lower end position.

• Two different safety positions, freely determinable for every individual motor output.

• Safety position with mains voltage return freely determinable and messaging over building.

• Automatic cascading of the outputs with mains voltage return and bus-safety functions to minimise power peaks.

• Plug and Play! Any time extendable with animeo RTS radio module (Ref. 1860105). Without additional wiring the four motors can be controlled

individually per radio using Somfy RTS technology.

• Alternatively the animeo KNX RTS Receiver (Ref. 1860191) can be used. Here, without additional wiring, up to 5 universal KNX radio binary

inputs can be gained (e.g., light ON/OFF with DIM).

Introduction

A complete parametering and programming is only possible when there is a power supply and KNX bus voltage on the KNX Motor Control-

ler. When only KNX bus voltage is present, only the physical address can be programmed.

Summary of Contents for animeo DRM
















































Search results

Summary of Contents for animeo DRM

Reviews:

Related manuals for animeo DRM

Brands by name

Popular brands

SOMFY animeo DRM, Instructions Manual

Search results

Summary of Contents for animeo DRM

Reviews:

Related manuals for animeo DRM

Brands by name

Popular brands