manualshive.com logo in svg

SOMFY animeo DRM, Instructions Manual

Share
Download
SOMFY animeo DRM Instructions Manual Download Page 19

 animeo KNX 4 AC MoCo · REF. 5071074 - 

19/47

Using push button binary input

With the parameter "Yes", four further menu index cards open (push button binary input 1…4). Now the local push button inputs can be 

connected over the corresponding objects (70-101). A conventional push button can thus be used for the most different of functions. For 

example, Switching, Venetian blind function, Dimming or Sending a value.

Using radio binary input

Selection options: 

 

No

 

  Yes

With the parameter "Yes" a menu index card opens (General: Radio binary input), over which five further menu index cards can be activated 

(Radio binary input 1...5). Now the radio channels can be connected over the corresponding objects (110-159). A radio transmitter can be 

used thus for the most different of functions.

Input group control

Selection options: 

 

Enabled

 

  Disabled

Over this parameter it is determined whether the input is blocked to the group control or is freed. Over this input all four motors are selected 

at the same time. Regardless of the parameter settings, the security settings (objects 27-36) have higher priority. If one of the security objects 

is active, the input to the group control is blocked.

 With a bus power failure this input is freed. Even if it is blocked over the parameter settings it can be used as an emergency service. With 

bus voltage return this input is blocked according to parameter settings or is freed.

Slats turn closed/turned 

ONLY WITH VENETIAN BLIND

Selection options: 

  Max. closed (255) / Max. turned (0)

 

  Max. closed (0) / Max. turned (255)

 

Max. closed (0) / Max. turned (255) 

If a value of "255" to the corresponding object is transmitted (13-16), the slats are closed at maximum.  

If a value of "0" to the corresponding object is transmitted (13-16), the slats are turned or opened at maximum.

 

Max. closed (0) / Max. turned (255) 

If a value of "0" on the corresponding object is transmitted (13-16), the slats are closed maximum. 

If a value of "255" on the corresponding object is transmitted (13-16), the slats are turned or opened  

maximum

Selection options: 

 

No

 

  Yes

Value (0/255)

Value (255/0)

Summary of Contents for animeo DRM
















































Reviews:

No comments

Brands by name

Popular brands

Load more brands