SOMFY animeo DRM Instructions Manual Download Page 43

Page: 43 / 47

animeo KNX 4 AC MoCo · REF. 5071074 -

43/47

Basic function

Selection options:



Venetian blind UP / DOWN



Switch/Dry contact



8-Bit value



Dimming



Venetian blind slow tilting

Long operation (move) after

Selection options:



0.5 seconds



0.3...5.0 seconds

This parameter defines the pressing time of the corresponding transmitter push button (Up/Down) which makes a distinction between the

sending of a short-term telegram (Up/Down) and a long-term telegram (Open/Close). If the time, for example, is set at 0.5 seconds, a long-

term telegram is generated after a longer pressing than 0.5 seconds. With a pressing duration which is shorter than 0.5 seconds, a short-

term telegram is generated.

Tilt slats (open/close) slowly by

Selection options:



Adjust 1/8



Adjust 100 % ... 1/64

This parameter defines the turn of the Venetian blinds which is transmitted as a telegram with a long pressing of the push button.

Functionality of the "my" push button

Selection options:



1-Bit value



8-Bit value



No function (no evaluation)

For a description please see "Function of the "my" button with Venetian blind UP/DOWN".

"Radio binary input 1...5"

Summary of Contents for animeo DRM
















































Search results

Summary of Contents for animeo DRM

Reviews:

Related manuals for animeo DRM

Brands by name

Popular brands

SOMFY animeo DRM, Instructions Manual

Search results

Summary of Contents for animeo DRM

Reviews:

Related manuals for animeo DRM

Brands by name

Popular brands