SOMFY animeo DRM Instructions Manual Download Page 11

Page: 11 / 47

animeo KNX 4 AC MoCo · REF. 5071074 -

11/47

No. Object name

Model

DPT_ID

Description

Motor 1-4 Move to IP 2

1 Bit

1.001

If a telegram with the value "1" is received on this communication

object, the blinds move to the Intermediate Positition (IP) 2 param-

etered in the ETS parameters. With the receiving of a telegram with

the value "0" on this communication object the blinds 1-4 move to

the upper end position.

Motor 1 Security, low prio

1 Bit

1.001

If a telegram with the value "1" is received on one of these com-

munication objects, the corresponding blind moves to the position

parametered in the ETS parameters. With the receiving of a telegram

with the value "0" on one of these communication objects, no op-

eration is carried out. Only when "Repeat last telegram after security

(Yes)" has been selected in the ETS parameters, can the operation

for the corresponding blind be carried out. If one of these commu-

nication objects is activated by a telegram with the value "1" and

on one of the communication objects 32-34 (Security, high prio)

a telegram is received with the value "1", the corresponding blind

move to the position parametered in the ETS (Security, high prio).

Motor 2 Security, low prio

1 Bit

1.001

Motor 3 Security, low prio

1 Bit

1.001

Motor 4 Security, low prio

1 Bit

1.001

Motor 1 - 4 Security, low prio

1 Bit

1.001

If a telegram with the value "1" is received on this communication

object, the blinds 1-4 move to the position parametered in the ETS

parameters. With the receiving of a telegram with the value "0" on

this communication object no operation is carried out. Only when

"Repeat last telegram after security (Yes)" has been selected in the

ETS parameters can the operation for the corresponding blinds 1-4

be carried out. If one of these communication objects is activated by

a telegram with the value "1" and on the communication object 36

(Security, high prio) a telegram is received with the value "1", the

blinds 1-4 move to the position parametered in the ETS (Security,

high prio).

Motor 1 Security, high prio

1 Bit

1.001

If a telegram with the value "1" is received on one of these com-

munication objects, the corresponding blind moves to the position

parametered in the ETS parameters. With the receiving of a telegram

with the value "0" on this communication object no operation is

carried out. Only when "Repeat last telegram after security (Yes)"

has been selected in the ETS parameters can the operation for the

corresponding blind be carried out. In this case, when an object for

"Security, low prio" is activated ("1"), the corresponding param-

etered position will be moved to.

Motor 2 Security, high prio

1 Bit

1.001

Motor 3 Security, high prio

1 Bit

1.001

Motor 4 Security, high prio

1 Bit

1.001

Motor 1 - 4 Security, high prio

1 Bit

1.001

If a telegram with the value "1" is received on this communica-

tion object, the blinds 1-4 move to the IP 2 parametered in the ETS

parameters. With the receiving of telegram with the value "0" on

this communication object no operation is carried out. Only when

"Repeat last telegram after security (Yes)" has been selected in the

ETS parameters can the operation for the blinds 1-4 be carried out.

In this case, when an object for "Security, low prio" is activated

("1"), the corresponding parametered position will be moved to.

Mains power failure (230 V)

1 Bit

1.002

A mains power failure is signaled with this communication object.

As soon as the mains voltage cuts out, a telegram with the value "1"

is sent to the bus. With return of mains voltage this communication

object sends the telegram with the value "0".

Motor 1 Feedback UP / DOWN

1 Byte

5.004

Through these communication objects, the actual position, based on

the learned-in move time (UP / DOWN direction) of the correspond-

ing blind, is sent to the bus. This kind of sending (on demand,

status change, cyclic) is set in the ETS parameters.

"0" = upper / "255" = lower.

Motor 2 Feedback UP / DOWN

1 Byte

5.004

Motor 3 Feedback UP / DOWN

1 Byte

5.004

Motor 4 Feedback UP / DOWN

1 Byte

5.004

Motor 1 Feedback slat

1 Byte

5.004

Through this communication objects, the actual slats position, based

on the learned-in turn time, is sent to the bus. This kind of sending

(on demand, status change, cyclic) is set in the ETS parameters. The

position, dependent of parameter settings on the menu list "Gen-

eral" is defined as follows:

"255" = slats max. closed / "0" = slats max. turned

"0" = slats max. closed / "255" = slats max. turned

Motor 2 Feedback slat

1 Byte

5.004

Motor 3 Feedback slat

1 Byte

5.004

Motor 4 Feedback slat

1 Byte

5.004

Summary of Contents for animeo DRM
















































Search results

Summary of Contents for animeo DRM

Reviews:

Related manuals for animeo DRM

Brands by name

Popular brands

SOMFY animeo DRM, Instructions Manual

Search results

Summary of Contents for animeo DRM

Reviews:

Related manuals for animeo DRM

Brands by name

Popular brands