manualshive.com logo in svg

Sofar solar 3.3K- 5.5KTL-X, User Manual

Share
Download
Sofar solar 3.3K- 5.5KTL-X User Manual Download Page 73

SOFAR 3.3K~12KTL-X

User manual

All rights reserved

©

Shenzhen SOFARSOLAR Co ., Ltd.

- 68 -

still exits after the replacement, please contact SOFAR
technical support.

ID87

Fan5 alarm

The fan5 is
fault

Check whether the external fan with blue heat-shrink
tubing is not working, if so, replace the fan, if the alarm
still exits after the replacement, please contact SOFAR
technical support.

ID88-89 Reserved Reserved

Reserved

ID90

Fan3 alarm

The fan3 is
fault

Check whether the internal fan is not working, if so,
replace the fan, if the alarm still exits after the replacement,
please contact SOFAR technical support.

ID91

Fan1 alarm

The fan1 is
fault

Check whether the external fan with blue heat-shrink
tubing is not working, if so, replace the fan, if the alarm
still exits after the replacement, please contact SOFAR
technical support.

ID92

Fan2 alarm

The fan2 is
fault

Check whether the external fan with red heat-shrink tubing
is not working, if so, replace the fan, if the alarm still exits
after the replacement, please contact SOFAR technical
support.

ID93

Lightning

protection

alarm

There has
Lightning
happen

Check the lightning protection module, if it’s undamaged,
please contact SOFAR technical support.

ID94

Software

version is

not

consistent

The Software
between the
control board
and the
communicatio
n board is not
consistent

Contact SOFAR technical support to upgrade software.

ID95

Communic

ation board

EEPROM

fault

The
Communicatio
n board
EEPROM is
fault

ID95~ID96 are internal faults of SOFAR inverter, turn
OFF the “DC switch”, wait for 5 minutes, then turn ON the
“DC switch”. Check whether the fault is rectified. If no,
please contact SOFAR technical support.

ID96

RTC clock

chip

anomaly

RTC clock
chip is fault

ID97

Invalid

Country

The Country is
InValid

Check the country setting according to Section 4.4 of this
user manual.

ID98

SD fault

The SD card is
fault

Please replace the SD card.

ID99-

ID100

Reserved

Reserved

Summary of Contents for 3.3K- 5.5KTL-X




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands