manualshive.com logo in svg

Sofar solar 3.3K- 5.5KTL-X, User Manual

Share
Download
Sofar solar 3.3K- 5.5KTL-X User Manual Download Page 61

SOFAR 3.3K~12KTL-X

User manual

All rights reserved

©

Shenzhen SOFARSOLAR Co ., Ltd.

- 56 -

↓

Wait for another test

Testing 81<S2...

↓

Wait

Test 81<S2 OK!

↓

Press “Down button”
to see the test results

81<S2:50.0Hz82ms

↓

Auto Test OK!

Logic interface

Enable or disable the logic interfaces, please refer to section 4.6 DRMs
Functions for details.

(B) “Event List” Interface as below:

Event List is used to display the real-time event records, including the total

number of events and each specific ID No. and happening time. User can

enter Event List interface through main interface to check details of

real-time event records, Event will be listed by the happening time, and

recent events will be listed in the front. Please refer to below picture:

Users press “Back” button and “Down” button in standard interface, then
enter into 2.Event List” interface.

Summary of Contents for 3.3K- 5.5KTL-X




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands