manualshive.com logo in svg

Sofar solar 3.3K- 5.5KTL-X, User Manual

Share
Download
Sofar solar 3.3K- 5.5KTL-X User Manual Download Page 4

SOFAR 3.3K~12KTL-X

User manual

All rights reserved

©

Shenzhen SOFARSOLAR Co ., Ltd.

II

Preface

Outline

Please read the product manual carefully before installation, operation or
maintenance. This manual contains important safety instructions and
installation instructions that must be followed during installation and
maintenance of the equipment.

Scope

This product manual describes the assembly, installation, commissioning,
and maintenance of the following inverters.

SOFAR 3.3KTL-X * ; SOFAR 4.4KTL-X ; SOFAR 5KTL-X *
[Australia] ; SOFAR 5.5KTL-X; SOFAR 6.6KTL-X; SOFAR
8.8KTL-X; SOFAR 11KTL-X; SOFAR 12KTL-X

(The models marked with“ *” should be available only for some designated
countries.)
Keep this manual where it will be accessible at all times.

Target Group

This manual is for qualified person (support person, service person are
qualified mentioned in this manual).

Symbols Used

This manual provides safety operation information and uses the symbol in
order to ensure personal and property security and use the inverter
efficiently when operating the inverter. You must understand these
emphasize information to avoid the personal injury and property loss.
Please read the following symbols which used in this manual carefully.

Danger indicates a hazardous situation which, if not avoided,
will result in death or serious injury.

Danger

Warning indicates a hazardous situation which, if not avoided,
could result in death or serious injury.

Warning

Caution indicates a hazardous situation, if not avoided, could
result in minor or moderate injury.

Caution

Summary of Contents for 3.3K- 5.5KTL-X




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands