manualshive.com logo in svg

Sofar solar 3.3K- 5.5KTL-X, User Manual

Share
Download
Sofar solar 3.3K- 5.5KTL-X User Manual Download Page 67

SOFAR 3.3K~12KTL-X

User manual

All rights reserved

©

Shenzhen SOFARSOLAR Co ., Ltd.

- 62 -

and AC wiring is correct, while the alarm occurs
repeatedly, contact SOFAR technical support to change the
grid over-voltage, under-voltage, over-frequency,
under-frequency protection points after obtaining approval
from the local electrical grid operator.

ID04

GridUFP

The power grid

frequency is

too low

ID05

PVUVP

The input
voltage is too
low

Check whether too few PV modules are series connected in
a PV string, thus the voltage(Vmp) of the PV string is
lower than the minimum operating voltage of SOFAR
inverter. If yes, adjust the number of series connected PV
modules to increase the voltage of the PV string to fit the
input voltage range of SOFAR inverter. SOFAR inverter
automatically returns to normal operating status after
correct adjustments.

ID06

Vlvrtlow

Low voltage
across

Check the AC wiring connection to the electric grid, if it’s
correct, please contact SOFAR technical support.

ID07-ID08 Reserved Reserved

Reserved

ID09

PvOVP

The input
voltage is too
high

Check whether too many PV modules are series connected
in a PV string, thus the voltage(Voc) of the PV string is
higher than the maximum input voltage of SOFAR
inverter. If yes, adjust the number of series connected PV
modules to decrease the voltage of the PV string to fit the
input voltage range of SOFAR inverter. SOFAR inverter
automatically returns to normal operating status after
correct adjustments.

ID10

IpvUnbala

nce

Input current is
not balanced Check the input mode(parallel mode/ independent mode)

setting of SOFAR inverter according to Section
4.5 of this user manual.

ID11

PvConfigS

etWrong

Incorrect input
mode

ID12

GFCIFault GFCI Fault

If the fault occurs occasionally, the possible cause is that
the external circuits are abnormal occasionally. SOFAR
inverter automatically returns to normal operating status
after the fault is rectified.
If the fault occurs frequently and lasts a long time, check
whether the insulation resistance between the PV array and
earth(ground) is too low, then check the insulation
conditions of PV cables.

ID13

PhaseSuen

ceFault

Phase
sequence
errors

If the alarm occurs occasionally, the possible cause is that
the electric grid is abnormal occasionally. SOFAR inverter
automatically returns to normal operating status when the
electric grid's back to normal.
If the alarm occurs frequently, check whether the grid
voltage/frequency is within the acceptable range. If no,
contact SOFAR technical support. If yes, check the AC

Summary of Contents for 3.3K- 5.5KTL-X




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands