background image

CPP100

SECTION 9

CPP1OPS

25/10/06

www.snellwilcox.com

Version 1 Issue 6

9.18

Enhancer cont.

The figure below shows the output of the enhancer. The solid line shows the enhanced signal and the dotted
line shows the input signal. The rise and fall time of the edges has been reduced i.e. the edges are sharper
without changing the position of the edge. The peak has been boosted which will also add to the appearance
of a sharper picture.

Enhancer output

The enhancer uses two different types of filtering in order to optimise the type and level of enhancement. The
two filters used are a broad bandpass filter and an adaptive filter.

The broad bandpass filter produces the highest enhancement levels at
3.375  MHz  for  luminance  whereas  the  adaptive  filter  has  the  highest  levels  of  enhancement  over  a  broader
range of frequencies.

The table below shows the filter settings used for the various levels of luminance enhancement:

Enhance Level

Filter Type

minimum

broad bandpass

medium

broad bandpass

maximum

adaptive

Coring

The aim of coring is to reduce or prevent the enhancement of noise in the picture using information from the
incoming  signal.  The  coring  function  uses  an  adjustable  threshold  window  that  can  be  adjusted  for  different
levels of noise in the incoming signal. The enhancer has adjustable coring levels that can be altered depending
on the quality of input pictures. The higher the coring level the less noise is enhanced.

Summary of Contents for Prefix Cpp100



















































































































Reviews: