Skoda Fabia II 2007 Workshop Manual Download Page 144

Page: 144 / 165

Disassembling and assembling the sliding sleeve/3rd and 4th

gear synchronizer body
1 - Spring (as of production date 06.09 the springs are longer) ⇒

Electronic Catalogue of Original Parts
2 - Sliding sleeve
3 - Synchronizer body
4 - Arresters for synchronizer body
– Slide the sliding sleeve over the synchronizer body.
The deeper recesses -arrow A- of the arresters in the synchron‐

izer body and the recesses -arrow B- in the sliding sleeve must

be positioned above one another.

Assembling the sliding sleeve/3rd, 4th and 5th gear synchronizer

body
The sliding sleeve is drawn over the synchronizer body.
– Insert the arresters in the deeper recesses -arrows- and mount

the springs by turning them 120°.
The angled end of the springs must grip into the hollow arrester

of the synchronizer body.

Fitting position of the sliding sleeve/3rd and 4th gear synchronizer

body
The groove on the front side -arrow- points towards the 4th gear.

Check 3rd, 4th and 5th gear synchronizer rings for wear
– Press the synchronizer ring on the cone of the sliding gear and

measure clearance -a- with a feeler gauge.

3.,4. and 5th gear

Installation dimen‐

sion

Wear limit

Clearance -a-

1.1 to 1.7 mm

0.5 mm

Fabia II 2007 ➤ , Fabia II 2009 ➤ , Fabia II 2011 ➤ , Rapid 2011 ➤ , R ...

Gearbox 02T - Edition 05.2014

140

Rep. gr.35 - Gears, shafts

Summary of Contents for Fabia II 2007






































































































































































Search results

Summary of Contents for Fabia II 2007

Reviews:

Brands by name

Popular brands

Skoda Fabia II 2007, Workshop Manual

Search results

Summary of Contents for Fabia II 2007

Reviews:

Brands by name

Popular brands