www.silverlinetools.com
7
996985
Running in the engine
• When the tool is new only run the engine at moderate speed
• Do not maintain high engine speed until the engine is fully run in
• The engine will not be capable of developing maximum power until the
end of the running in period
• When first using the tool, stop and make sure that all nuts and screws
are securely fastened and tighten them as necessary
• Do not use fuels containing methanol, or ethanol, as these may cause
internal damage to the fuel tank, and fuel lines
Servicing
• It is recommended that you get your tool serviced shortly after its first use
• In normal use, have the tool serviced regularly
• Do not attempt to alter any of the components of this tool. To do so
would not only invalidate your guarantee, but may also result in injury to
yourself, or others around you
• Always have your tool serviced at an authorised service centre
Storage
• When you have finished using the tool, clean it completely
• Be careful not to hit or cut the fuel tank, or fuel lines, when it is placed
on the ground
• Do not let the tool fall, or it may be damaged and become unsafe
• Store the tool away from direct sunlight
• Ensure that fuel and oil is stored in a safe place, away from heat, direct
sunlight, any source of ignition, and out of reach of children
Whenever the machine is out of use for an extended period
of time, proceed as follows:
• Empty the fuel tank completely
• Protect all metal engine parts from corrosion by coating them with oil
• Remove the spark plug, put a few drops of oil into the cylinder and then
pull the recoil starter 2 to 3 times in order to distribute the oil evenly
• Replace the spark plug
• Never leave the tool running unattended
• Always wait until the machine has come to a complete stop before
leaving it
• Never leave the machine unattended when parts are still hot
• Never leave machine unattended where children may have access to it
THIS PRODUCT PRODUCES POISONOUS EXHAUST FUMES AS SOON AS
THE ENGINE IS RUNNING. THESE GASES MAY BE COLOURLESS AND
ODOURLESS. TO REDUCE THE RISK OF SERIOUS OR FATAL INJURY, NEVER
RUN THE MACHINE INDOORS, OR IN POORLY VENTILATED AREAS. ENSURE
PROPER VENTILATION WHEN WORKING IN TRENCHES OR OTHER CONFINED
SPACES.
6.5hp Clean Water Pump
Unpacking your Tool
Carefully unpack and inspect your tool. Fully familiarise yourself with all
features and functions of it.
Ensure that all parts of the tool are present and in good condition. If any
parts are missing or damaged, have such parts replaced before attempting
to use this tool.
Pump placement
• For best performance the pump should be placed as close to the water
as safely possible and hoses should be no longer than necessary. This
enables the pump to produce the greatest output with the minimum self
priming time. As head (total pumping height) increases, so pump output
decreases. Length, type and size of discharge hoses can significantly
affect pump output
• Discharge head capability is always greater than suction head capability
so it is important that the suction head is the shorter part of total head
1
Water Filter
2
Hose 50mm (2") int. dia. - Not Supplied
3
Hose Clamp (x 2)
4
Hose Coupler (x 2)
5
Rubber Seal (x 2)
6
Fuel Tank Cap
7
Exhaust Outlet
8
Fuel Lever
9
Choke Lever
10 Engine Speed Control
11 Air Filter Housing
12 Ignition Switch
13 Dipstick
14 Starter Handle
15 Spark Plug Socket
16 Oil Filler Neck
17 Fuel Drain Screw
18 Sump Plug
19 Air Filter Retainer
20 Air Filter Element
21 Spark Plug
22 Ignition Lead
23 Water Drain Plug
24 Water Inlet
25 Water Outlet
26 Water Priming Point
Product Familiarisation
996985_Z1MANPRO1.indd 5
27/06/2011 12:29
