Silverline 996985 Manual Download

Page: 6 / 30

Remove adjusting keys

• Where adjusting keys exist, ensure they are removed prior to using the

tool. Always check to see that keys and adjusting devices are removed
from the tool before use

Clean the work area

• Accidents can occur where benches and work areas are cluttered or

dirty. Keep floors clear and avoid working where the floor is slippery. If
working outdoors, be aware of all potential slip and trip hazards before
using this tool

Trained, competent persons

• This tool should be used by trained, competent persons only

Children and pets

• Keep children and pets at a safe distance from the work area. Lock tools

away where children cannot gain access

Use the correct tool

• Do not force or attempt to use a tool for a purpose for which it was not

designed. This tool is not intended for industrial use

Wear suitable clothing and footwear

• Do not wear loose fitting clothing, neckties, jewellery, or other

items which may become caught. Wear non-slip footwear or, where
appropriate, footwear with protective toe caps. Long hair should be
covered or tied back

Keep your balance

• Do not over-reach. Keep proper footing at all times and do not use tools

when standing on an unstable surface

Accessories

• The use of any attachment or accessory, other than those mentioned in

this manual, could be dangerous and result in damage or injury, and may
invalidate your warranty

Never stand on your tool

• Standing on your tool or its stand could cause serious injury if the tool is

tipped or collapses. Do not store materials above or close to the tool in such
a way that a person might stand on the tool to reach the stored items

Secure work

• Where possible, always secure work. If appropriate, use a clamp or vice

so that both hands are free to operate the tool

Check for damaged or missing parts

• Before each use, check if any part of the tool is damaged or missing.

Carefully check that it will operate properly and perform its intended
function. Check alignment of moving parts for binding. Any guard or other
part that is damaged should be immediately repaired or replaced by an
authorised service centre.

DO NOT USE IF DEFECTIVE

Internal Combustion Safety

Dangerous environment

• Do not use petrol tools in damp or wet conditions, or expose them to

rain. Provide adequate surrounding work space and keep area well lit.
Do not use petrol tools where there is a risk of explosion or fire from
combustible material, flammable liquids, flammable gases, or dust of an
explosive nature

Protect yourself from vibration

• Hand held tools may produce vibration. Vibration can cause disease.

Gloves to keep the operator warm may help to maintain good blood
circulation in the fingers. Hand held tools should not be used for long
periods without a break

Protect your hearing

• Always wear suitable hearing protection when tool noise exceeds 80dB.

It is the responsibility of the user to ensure that other people near to
where the tool is to be used are also suitably protected

Switch off before connecting

• Ensure that the engine is stopped before connecting any accessories to

the tool. If the tool stops unexpectedly make sure that the engine is not
running before attempting to check the tool

Specification

   Engine: ........................................ 4 stroke OHC
   Power: ........................................ 6.5hp
   Fuel: ............................................ Unleaded
   Oil  type: ...................................... 10W-30
   Oil  Qty:   ....................................... 0.6L
  Spark plug: .................................. Torch F6TC, Champion

     N9YC or equivalent
  Spark plug gap:........................... 0.5 – 0.7mm
  Fuel tank capacity: ...................... 3.6L
   Max continuous run time: ........... 14H
   Maximum pump rate:.................. 27m

   Pumping  elevation: ..................... 30m
  Suction head ............................... 7m
  Suction hose (reinforced) ............ 50mm diameter
  Discharge hose ........................... 50mm diameter
  Sound Level ................................ 99dB(A)

The sound intensity level for the operator may exceed

85dB(A) and sound protection measures are necessary.

As part of our ongoing product development, specifications

of Silverline products may alter without notice.

General Safety

Carefully read and understand this manual and any label attached to
the tool before use. Keep these instructions with the product for future
reference. Ensure all persons who use this product are fully acquainted
with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk
factors. Use with caution. If you are at all unsure of the correct and safe
manner in which to use this tool, do not attempt to use it.

Keep guards in position

• Where guards exist keep them in position, in good working order,

correctly adjusted and aligned. Never attempt to use a tool if any of
the supplied guards are missing. If any guards are damaged, replace
before use

Description of Symbols

The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.

  Wear hearing protection.
  Wear eye protection.
  Wear breathing protection.
  Wear head protection.

Wear hand protection.

Read instruction manual.

Do not use petrol tools where there is a risk of explosion or

fire from combustible material, flammable liquids, flammable
gases, or dust of an explosive nature

If the engine has been running it will be very hot.

DO NOT