www.silverlinetools.com
7
1500W Sander Polisher
129659
WARNING
: The Hook & Loop Backing Pad is tightened by hand. Take
care not to cross-thread or over-tighten.
3. Release the Spindle Lock Button
Fitting bonnets, polishing sponges and discs
• The Hook & Loop Polishing Bonnet, 80 Grit Hook & Loop Sanding Disc
and other polishing accessories, such as polishing sponges (not included)
can be pressed onto the face of the Hook & Loop Backing Pad (10)
• Slowly pull the fitted attachment off the Hook & Loop Backing Pad to
remove
Note
: Always make sure both hook & loop surfaces are free of dirt and
debris prior to attaching any items (also see remarks ‘Maintenance’
section).
Operation
WARNING
: ALWAYS wear eye protection, adequate respiratory and
hearing protection, as well as suitable gloves, when working with this tool.
Switching on and off
WARNING
: Never switch the tool on or off when it is in contact with the
workpiece. This can cause serious injury to the operator and will
significantly shorten the service life of the On/Off Trigger Switch (1).
1. Connect the machine to the power supply
2. Hold the tool securely with both hands with one hand on the Rear Handle
(2) and the other hand on the Auxiliary Handle (5)
3. Press in the Lock-Off Button (3)
4. Allow the tool to reach the speed required before bringing the machine
into contact with the workpiece
5. Remove the sander/polisher from the workpiece before switching off
6. To stop the machine, release the On/Off Switch
WARNING
: ALWAYS wait until the machine has come to a standstill
before placing it down.
Adjusting the tool speed
• The speed of the machine is controlled using the Speed Control Dial (4): A
higher number indicates a higher speed setting
WARNING
: Always set the speed control dial to the correct speed for
the task at hand.
WARNING
: Never exceed the maximum speed of the installed
accessory.
Polishing tips
• Ensure the area to be polished is clean and dry
• Choose only polishing compounds that are compatible with the material
to be polished, and with the method of application. Read and understand
all information supplied with your polishing compound before use
• If using polishing sponges, apply polishing compound evenly to the
polishing sponge and place the sponge against the work surface
• Hold the machine securely, using both hands, by the handles provided.
The polishing sponge should make only light contact with the work
surface
• Switch on the machine and work across the surface using a wide
'sweeping' motion. Stop and apply extra compound as required
• When the entire surface has been covered, stop the machine and allow
the compound to dry (follow manufacturer’s guidance)
• Attach a clean polishing bonnet to the machine and work across the
surface as before, until all visible polishing compound is removed
Sanding tips
WARNING
: This machine is primarily designed as a polishing tool. It is
suitable for light duty sanding tasks, e.g. fine sanding as a preparation to
polishing, but it has not been designed to remove large amounts of material.
Use a different type of sander, e.g. a belt sander, should this be required.
WARNING
: NEVER use this machine for wet sanding.
WARNING
: ALWAYS use adequate respiratory protection when sanding.
• Allow the machine to reach the required speed before bringing the
sanding paper into contact with the workpiece
• Start with a coarse grit paper and work through progressively finer grit
papers until the desired finish is achieved
• Apply only moderate pressure to the sander. Pressing too hard onto the
work surface may overheat the motor or damage the work surface
• Sand evenly over the work surface. The machine works in a rotary
motion so it is not necessary to work with the grain
• Only use the sander 'flat on' to the work. Tilting the sander onto its edge
will damage the workpiece
Accessories
• A range of accessories for your sander polisher, including polishing
sponges and lambswool bonnets, sanding sheets and polishing
compounds, is available from your Silverline stockist. Spare parts can be
obtained from www.toolsparesonline.com
Maintenance
WARNING
: ALWAYS disconnect from the power supply before carrying
out any inspection, maintenance or cleaning.
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear.
Repairs should be carried out by an authorised Silverline service centre.
This advice also applies to extension cords used with this tool
Cleaning
WARNING
: Be especially careful to clean the machine thoroughly if used for
both wood and metal. Sparks from metal work can easily ignite wood dust.
• Keep your tool clean at all times. Dirt and dust will cause internal parts
to wear quickly, and shorten the machine’s service life. Clean the body of
your machine with a soft brush, or dry cloth. If available, use clean, dry,
compressed air to blow through the ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do
not use alcohol, petrol or strong cleaning agents
• Never use caustic agents to clean plastic parts
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable
spray lubricant
Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure,
or visible sparking
• If you suspect that the brushes may be worn, have them replaced at an
authorised Silverline service centre
Note
: One set of Spare Carbon Brushes is supplied with this tool.
• To replace the brushes:
1. remove the Brush Access Caps (11) from both sides of the machine
2. Remove the worn brushes and replace
3. Replace the Brush Access Caps
• Alternatively, have the machine serviced at an authorised Silverline
service centre
129659_Z1MANPRO1..indd 7
08/06/2016 11:01
