manualshive.com logo in svg

Silicon Laboratories Si4430, Manual

Share
Download
Silicon Laboratories Si4430 Manual Download Page 81

Si4430

Preliminary Rev. 0.4

81

Reset value = xxxxxxxx

When any of the Interrupt/Status Register 2 bits change state from 0 to 1 the control block will notify the
microcontroller by setting the nIRQ pin LOW if it is enabled in the Interrupt Enable 2 register. The nIRQ pin will go
to HIGH and all the 

enabled

 interrupt bits will be cleared when the microcontroller reads this address. If any of

these bits is not enabled in the Interrupt Enable 2 register then it becomes a status signal that can be read anytime
in the same location and will not be cleared by reading the register.

Register 04h. Interrupt/Status 2

Bit

D7

D6

D5

D4

D3

D2

D1

D0

Name

iswdet

ipreaval

ipreainval

irssi

iwut

ilbd

ichiprdy

ipor

Type

R

R

R

R

R

R

R

R

Bit

Name

Function

7

iswdet

Sync Word Detected.

When a sync word is detected this bit will be set to 1.

6

ipreaval

Valid Preamble Detected.

When a preamble is detected this bit will be set to 1.

5

ipreainval

Invalid Preamble Detected.

When the preamble is not found within a period of time set by the invalid preamble detec-
tion threshold in Register 54h, this bit will be set to 1.

4

irssi

RSSI.

When RSSI level exceeds the programmed threshold this bit will be set to 1.

3

iwut

Wake-Up-Timer.

On the expiration of programmed wake-up timer this bit will be set to 1.

2

ilbd

Low Battery Detect.

When a low battery event is been detected this bit will be set to 1. This interrupt event is 
saved even if it is not enabled by the mask register bit and causes an interrupt after it is 
enabled.

1

ichiprdy

Chip Ready (XTAL).

When a chip ready event has been detected this bit will be set to 1.

0

ipor

Power-on-Reset (POR).

When the chip detects a Power on Reset above the desired setting this bit will be set to 1.

Summary of Contents for Si4430

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands