manualshive.com logo in svg

Siemens TS2000, Service Manual, Page: 47 / 65

Share
Download
Siemens TS2000 Service Manual Download Page 47

 

6-1

6.  TROUBLESHOOTING 

NOTE: 

 

 

1)

 

The effectiveness of any repair and part replacement must 

be verified by a functional test.  Refer to Section 7.4. 
 
2)

 

Each intervention (replacement or repair) must be recorded 

in the “record of service visits” section of the manual. 
 
3) Replace “blown” fuses ONLY with the same type and 
rating as marked on the safety label adjacent to the power 
inlet, housing the fuse. 
 
Be sure to unplug the power supply cord from the wall socket 
BEFORE attempting to remove and/ or check the main power 
fuse. 

Every sophisticated system has the potential for an occasional problem to 
occur.  This section explains how to diagnose and correct these problems. 

In the following table, “Reboot the system” means: use the exit button to shut 
down the system properly, turn the power off, wait 4-5 seconds and then turn 
the power on again. 

6.1  Error Messages 

6.1.1   Displayed Error Messages 

Messages 

Solution 

Replay Parameters Not 
Found. 

• 

Try replaying another patient file. If 

still unable to complete the command, 
reboot the system. 

Probe Not Connected. 

• 

Check the cable connection for 

probe(s). If the system still does not 
respond appropriately, then reboot the 
system. 

• 

Replace the probe. 

Error 327: Has no... 

• 

Check that the parallel card is properly 

installed. 

Continued next page: 

SPB7-520.840.01.01.02

Summary of Contents for TS2000


































































Reviews:

No comments