Siemens SIMATIC S7-1200 CP 1243-8 IRC Operating Instructions Manual Download Page 83

Page: 83 / 230

Configuration

4.9 Serial interface

CP 1243-8 IRC
Operating Instructions, 02/2018, C79000-G8976-C385-03

Select the interface to create a new WAN network. Alternatively:
In the parameter group "Network interface with" of the interface:
–

Using the "Add new subnet" button

On the interface in the device icon of the CP
–

Using the shortcut menu "Create subnet"

–

Graphically by dragging (holding the mouse pointer pressed) to the interface symbol of

the communications partner

A new WAN network is created that adopts the network type from the connected

interface.

Network representation of a classic WAN
A classic WAN network is displayed in blue.

Figure 4-2

Serial interface of a TIM and a CP 1243-8 IRC connected via classic WAN.

Networking the Ethernet interface

You network the Ethernet interface in the same was as the serial interface.
The following example shows two modules with one MSC connection via Ethernet.

Figure 4-3

MSC connection between a TIM and a CP

WAN address

Here you assign the WAN address of the CP. For the meaning, refer to ST7 (Page 61).

●

WAN address
For every networked interface in a classic ST7 network a WAN address is assigned. This

is unique throughout the network.
Since telecontrol connections can run via several network nodes and node stations,

unique addressing of the interfaces involved is necessary.
The WAN address is configured in the parameter group "WAN parameters" of the serial

interface.

You configure the subscriber numbers in the parameter group "Station address" see section

Subscriber numbers (Page 103).

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Operating Instructions Manual, Page: 83 / 230

Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews: