Siemens SIMATIC S7-1200 CP 1243-8 IRC Page 80 Operating Instructions Manual Download

Page: 80 / 230

Configuration

4.9 Serial interface

CP 1243-8 IRC

Operating Instructions, 02/2018, C79000-G8976-C385-03

Configuration of the serial interface

You configure depending on the application or the firmware version of the CP.

●

CP as replacement for TIM 3V-IE Advanced
Use a CP with firmware V2.1.
–

You have exported the configuration data of the substitute for the CP

(PROXY CP1243-8 IRC) from STEP 7 V5 as a text file with the SDB content.

–

You import this text file in STEP 7 Basic in the parameter group Partner stations

(Page 90).

●

CP for new systems
Use a CP with firmware V3.
You configure the serial interface only in STEP 7 Basic, refer to the section below.

SMS

If the CP is intended to use the sending of SMS messages, you need to activate the function:

●

CP with firmware V2.1
Enable or disable the sending of SMS messages at this point and assign the number of

the SMSC (Short Message Service Center).

●

CP with firmware V3
You enable SMS and configure the SMSC in the parameter group SMSC (Page 103).

4.9.2

Configuring a TS module

Configuration of the serial interface is only possible and necessary for the CP with a

firmware version as of V3.
To be able to configure the serial interface, you must first insert the suitable TS module in

STEP 7. Without a configured TS module, the serial interface is not displayed and the CP is

only displayed with the green symbol for the Ethernet interface.

Inserting a TS module for the serial interface

To insert a TS module in STEP 7, follow the steps outlined below:
1.

Open the device view of the CP.
When the network view is open: Open the device view by double-clicking on the CP or by

clicking on the work area "Device view".

Select the CP in the device view.
The CP is displayed with a blue frame.

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands