manualshive.com logo in svg

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Operating Instructions Manual, Page: 52 / 230

Share
Download
Siemens SIMATIC S7-1200 CP 1243-8 IRC Operating Instructions Manual Download Page 52

Installation, connecting up, commissioning 

 

3.2 Installing, connecting up and commissioning 

 

CP 1243-8 IRC 

52

 

Operating Instructions, 02/2018, C79000-G8976-C385-03 

 

CAUTION 

Ground the connecting cable of a TS module separately 
Connect the connecting cable of a TS module to the periphery (e.g. modem) separately to 

functional ground. 

 

 

Note 
Prior to mounting a TS module 
For information on mounting a TS module, also read the appropriate sections in the device 

manual, see /4/ (Page 226). 

 

 

Note 
Power supply from the power outputs of the CPU 
The external power supply of the CP must be supplied via the power outputs of the CPU for 

the sensor supply. 
Keep within the maximum load of the power output of the CPU, see /1/ (Page 225). 
You will find data relating to the current consumption and power loss of the CP in the section 

Technical data (Page 183). 

 

 

Note 
Turning off the station when plugging/pulling the CP 
Do not only turn off the power supply to the CP. Always turn off the power supply for the 

entire station. 

 
 

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Reviews:

No comments