Siemens SIMATIC S7-1200 CP 1243-8 IRC Page 74 Operating Instructions Manual Download

Page: 74 / 230

Configuration

4.8 Ethernet interface

CP 1243-8 IRC

Operating Instructions, 02/2018, C79000-G8976-C385-03

4.8.5.2

TCP connection monitoring

The settings made here apply globally to all configured TCP connections of the CP.
With DNP3:

Note the option of overwriting the values configured here for individual communications

partners, refer to the section Partners (DNP3 / IEC) (Page 91).

●

TCP connection monitoring time
Function: If there is no data traffic within the TCP connection monitoring time, the CP

sends a keepalive frame to the communications partner.
Default setting: 180 s. Permitted range: 1...65535 s.
–

The parameter below the Ethernet interface
The monitoring time is configured for the Ethernet interface globally for all TCP

connections. The parameter is preset to 180 seconds as default.

–

The parameter below "Partner stations"
The parameter "TCP connection monitoring time" occurs again with the individual

partners in the parameter group "Connection to partner". This parameter applies only

to the individual partner. The value of 180 seconds preset on the Ethernet interface is

adopted for the individual partners.
If for any reason you want to change the value of the TCP connection monitoring time

for individual partners, you can adapt the value for every partner individually in

"Partner stations". If. for example, you want to check the connection at shorter

intervals, reduce the value.

●

TCP keepalive monitoring time
After sending a keepalive frame, the CP expects a reply from the communications partner

within the keepalive monitoring time. If the CP does not receive a reply within the

configured time, it terminates the connection.
Default setting: 10 s. Permitted range: 1...65535 s.
–

The parameter below the Ethernet interface
The monitoring time is configured for the Ethernet interface as a global setting for all

TCP connections.

–

The parameter below "Partner stations"
As with the TCP connection monitoring time, the value of "Partner stations" can be

adapted for each partner individually.

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands