Siemens SIMATIC S7-1200 CP 1243-8 IRC Page 196 Operating Instructions Manual Download

Page: 196 / 230

Accessories

C.1 TS modules

CP 1243-8 IRC

196

Operating Instructions, 02/2018, C79000-G8976-C385-03

Note
Use the supplied cable with ferrite to comply with EMC values and make sure that the ferrite

is on the module side.

To use the TS Module Modem outside Germany, you can fit a country-specific TAE

connector onto the RJ11 connector of the phone cable. For Germany, a TAE6N connector is

supplied. In some countries, telephone jacks with RJ-11 sockets are available, so that the

telephone cable can be used without TAE connectors.

Specifications

●

Dimensions (WHD): 30 x 100 x 75 mm

●

Weight: 98 g

●

ITU transmission standards:
V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34, V.34x, K56flex, V.90, V.92

●

Error correction and data compression

●

a/b port

●

Hayes command set (AT)

●

All data formats

●

Dialing mode: Multifrequency signaling (DTMF), pulse dialing

National approvals

The TS Module Modem is designed so that worldwide use is possible. When installing and

operating the TS Module Modem, keep to the country-specific laws and special features.
The TS module has a telecommunications approval in the following countries:

•

Australia

•

Iceland

•

Poland

•

Belgium

•

Italy

•

Portugal

•

Bulgaria

•

Canada

•

Romania

•

Denmark

•

Latvia

•

Sweden

•

Germany

•

Lithuania

•

Switzerland

•

Estonia

•

Luxembourg

•

Slovakia

•

Finland

•

Malta

•

Slovenia

•

France

•

New Zealand

•

Spain

•

Greece

•

Netherlands

•

Czech Republic

•

Great Britain

•

Norway

•

Hungary

•

Ireland

•

Austria

•

USA

•

Cyprus

For information on approval in other countries, please contact Technical Support.

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands