Siemens SIMATIC S7-1200 CP 1243-8 IRC Page 177 Operating Instructions Manual Download

Page: 177 / 230

Diagnostics and upkeep

6.5 Processing status of messages

CP 1243-8 IRC
Operating Instructions, 02/2018, C79000-G8976-C385-03

177

6.5

Processing status of messages

Processing status

If the option "Enable identifier for processing status" is enabled in the message editor for a

message, a status is output on the CP that provides information about the processing status

of the sent message. The status is written to a PLC tag of the type DWORD. Select this tag

via the "PLC tag for processing status" box.
The meaning of the statuses is as follows:

Table 6- 1

SMS: Meaning of the status ID output in hexadecimal format

Status Meaning
0000

Transfer completed free of errors

0001

Error in the transfer, possible causes:

•

SIM card invalid

•

No network

•

Wrong destination phone number (number not reachable)

Table 6- 2

E-mails: Meaning of the status ID output in hexadecimal format

Status Meaning
0000

Transfer completed free of errors

82xx

Other error message from the e-mail server
Apart from the leading "8", the status corresponds to the three-digit error number of the

SMTP protocol.

8401

No channel available
Possible cause: There is already an e-mail connection via the CP. A second connection

cannot be set up at the same time.

8403

No TCP/IP connection could be established to the SMTP server.

8405

The SMTP server has denied the login request.

8406

An internal SSL error or a problem with the structure of the certificate was detected by the

SMTP client.

8407

Request to use SSL was denied.

8408

The client could not obtain a socket for creating a TCP/IP connection to the mail server.

8409

It is not possible to write via the connection. Possible cause: The communications partner

reset the connection or the connection aborted.

8410

It is not possible to read via the connection. Possible cause: The communications partner

terminated the connection or the connection was aborted.

8411

Sending the e-mail failed. Cause: There was not enough memory space for sending.

8412

The configured DNS server could not resolve specified domain name.

8413

Due to an internal error in the DNS subsystem, the domain name could not be resolved.

8414

An empty character string was specified as the domain name.

8415

An internal error occurred in the cURL module. Execution was aborted.

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands