manualshive.com logo in svg

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Operating Instructions Manual

The Siemens SIMATIC S7-1200 CP 1243-8 IRC is an advanced industrial communication processor that enhances connectivity for your automation systems. Ensure proper setup and operation with the Operating Instructions Manual, which you can download for free at manualshive.com. This comprehensive manual provides valuable insights for maximizing the potential of your Siemens product.

Share
Download
background image

 

Application and functions 

 

1.9 Configuration examples 

CP 1243-8 IRC 
Operating Instructions, 02/2018, C79000-G8976-C385-03 

29

 

Telecontrol communication - wireless network 

In this example, the S7 stations communicate with the master station via an IP-based private 

wireless network. For this application, suitable IP-based wireless devices must be used. 
The CPs are connected via their Ethernet interface. In this configuration as well, an Ethernet 

network needs to be configured in STEP 7 V5. 

 

Figure 1-5 

Communication via an IP-based private wireless network 

Communication via an analog wireless network with communication according to the RS-232 

standard is also possible. In this case, the CP 1243-8 would need to be connected to the 

wireless device via a TS module RS-232. In this configuration a dedicated line network 

would need to be configured in STEP 7 V5. 

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Reviews:

No comments

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

IBM AS/400 Hardware User Manual preview
AS/400
Brand: IBM Pages: 104
IBM System Storage TS3100 Setup, Operator, And Service Manual preview
System Storage TS3100
Brand: IBM Pages: 375
Jabra A330 Multiuse User Manual preview
A330 Multiuse
Brand: Jabra Pages: 15
LaCie 5big Network 2 Datasheet preview
5big Network 2
Brand: LaCie Pages: 4
LaCie d2 Network 2 Datasheet preview
d2 Network 2
Brand: LaCie Pages: 4
Salusfin SF-930EU User'S Installation Manual preview
SF-930EU
Brand: Salusfin Pages: 6
Parker ACR1200 Hardware Manual preview
ACR1200
Brand: Parker Pages: 50
Longshine LCS-8131G3 User Manual preview
LCS-8131G3
Brand: Longshine Pages: 27
ZALMAN RESERATOR2 Installation And Operational Manual preview
RESERATOR2
Brand: ZALMAN Pages: 18
Procool SP480 Series Instructions preview
SP480 Series
Brand: Procool Pages: 2
H3C SecPath F1070 Manual preview
SecPath F1070
Brand: H3C Pages: 68
Xilinx ML506 Quick Start Manual preview
ML506
Brand: Xilinx Pages: 29
OWC ACCELSIOR 8M2 Assembly Manual & User Manual preview
ACCELSIOR 8M2
Brand: OWC Pages: 9
Cognex 800-5815-1 Installation And Reference Manual preview
800-5815-1
Brand: Cognex Pages: 57
Zhone 891630 System Reference Manual preview
891630
Brand: Zhone Pages: 494
ekwb SLIM 120 User Manual preview
SLIM 120
Brand: ekwb Pages: 36
Compaq ProLiant 4500 Quick Start Manual preview
ProLiant 4500
Brand: Compaq Pages: 2
ADTRAN NetVanta 1224 Quick Start Manual preview
NetVanta 1224
Brand: ADTRAN Pages: 2

Brands by name

Popular brands

Load more brands