manualshive.com logo in svg

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Operating Instructions Manual

The Siemens SIMATIC S7-1200 CP 1243-8 IRC is an advanced industrial communication processor that enhances connectivity for your automation systems. Ensure proper setup and operation with the Operating Instructions Manual, which you can download for free at manualshive.com. This comprehensive manual provides valuable insights for maximizing the potential of your Siemens product.

Share
Download
background image

Accessories 

 

C.1 TS modules 

 

CP 1243-8 IRC 

200

 

Operating Instructions, 02/2018, C79000-G8976-C385-03 

Specifications 

●

 

Dimensions (WHD): 30 x 100 x 75 mm 

●

 

Weight: 100 g 

●

 

Type of traffic: Full duplex 

●

 

Transmission mode: Asynchronous 

●

 

Signals: TXD, RXD, DSR, CTS, RTS, DTR, DCD 

●

 

Transmission speed: 2400...115200 bps 

●

 

Frame format: 8 data bits (LSB first), no parity bit, 1 stop bit 

●

 

Standard: RS-232 

●

 

D-sub male connector: 9-pin, male (PC COMx) 

C.1.5

 

TS Module GSM 

 

 

Note 
The device is designed for industrial use. 

 

Product package 

 

Designation 

Article number 

TS Module GSM 

6GK7 972-0MG00-0XA0 

Properties 

The TS Module GSM has an interface for the connection of a GSM/GPRS antenna and a 

tray for a SIM card. 
The antenna connection and the slot for the SIM card are located behind the lower front 

panel. 

Accessories 

For the antenna, refer to the section Antennas (Page 208). 

CSD data connection (Circuit Switched Data) 

For outgoing calls, the TS Module GSM supports GPRS and CSD data connections. 
For incoming calls, only CSD data connections are accepted. 

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Reviews:

No comments

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

M-Audio Computer Quick Start Manual preview
Computer
Brand: M-Audio Pages: 10
Cabletron Systems Netlink FRX4000 Installation And Setup Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 8
Cabletron Systems 9C300-1 Upgrade Instructions preview
9C300-1
Brand: Cabletron Systems Pages: 4
Xilica Audio Design neutrino series Quick Start Manual preview
neutrino series
Brand: Xilica Audio Design Pages: 26
ICT Protege PRT-PX16-PCB Installation Manual preview
Protege PRT-PX16-PCB
Brand: ICT Pages: 34
Avolites Titan One Quick Start Manual preview
Titan One
Brand: Avolites Pages: 24
ZyXEL Communications ZyXEL ZyAIR B-120 Quick Installation Manual preview
ZyXEL ZyAIR B-120
Brand: ZyXEL Communications Pages: 20
ekwb EK-Loop Modulus Series User Manual preview
EK-Loop Modulus Series
Brand: ekwb Pages: 7
Xantech CC12 Installation Instructions preview
CC12
Brand: Xantech Pages: 4
Abocom WM5504 User Manual preview
WM5504
Brand: Abocom Pages: 70
ADC 150-204-100-03 User Manual preview
150-204-100-03
Brand: ADC Pages: 29
Vertilon SIB064B User Manual preview
SIB064B
Brand: Vertilon Pages: 21
Aaeon PER-C41L Quick Installation Manual preview
PER-C41L
Brand: Aaeon Pages: 22
AA WIRELESS AAWireless-002 User Manual preview
AAWireless-002
Brand: AA WIRELESS Pages: 55
RadioLAN DockLINK User Manual preview
DockLINK
Brand: RadioLAN Pages: 118
Asus AAEON BOXER-8256AI User Manual preview
AAEON BOXER-8256AI
Brand: Asus Pages: 55
Asus AAM6020VI-T4 User Manual preview
AAM6020VI-T4
Brand: Asus Pages: 40
Asus Aaeon ICS-6280 User Manual preview
Aaeon ICS-6280
Brand: Asus Pages: 75

Brands by name

Popular brands

Load more brands