Siemens SIMATIC S7-1200 CP 1243-8 IRC Page 160 Operating Instructions Manual Download

Page: 160 / 230

Configuration

4.18 Data points

CP 1243-8 IRC

160

Operating Instructions, 02/2018, C79000-G8976-C385-03

●

PULSE_ON/OFF
The function is coded by the master via a "Qualifier of command". The following codings

are evaluated by the communication module in the station:
–

QU (Type 1.1) <1> short pulse duration
Corresponding parameter for the module: "Short pulse duration"

–

QU (Type 1.1) <2> long pulse duration
Corresponding parameter for the module: "Long pulse duration"

–

S/E (Type 6) <0> execute
Corresponding parameter for the module: "Command execution mode"

–

S/E (Type 6) <1> select
Corresponding parameter for the module: "Command execution mode"

For parameter assignment see below.

DNP3
The two functions are encoded by the master via the control code of the object.

●

LATCH_ON/OFF
The function latches the value of a command as described above.

●

PULSE_ON/OFF
The function evaluates the number of pulses and duration.
The master sends a "Control Code" to the station with the "PULSE_ON" function with

information on the "Count", "On-time" and "Off-time". The data point of the

communication module in the station evaluates this information via the parameters "Max.

pulse duration", "Pulse duration replacement time" and "Max. number of pulses".

The following encodings of the control code are evaluated by the data point:

Table 4- 10 DNP3 Control Codes

Receipt of:

Reaction of data point upon activation of:

Control

Code

Trip-

Code

Operation

Type field

PULSE_ON / OFF

LATCH_ON / OFF

0x01

NUL

PULSE_ON The output is set to 1 for the

"Max. pulse duration".

The command is rejected.

0x03

NUL

LATCH_ON The command is rejected.

The output is set permanently

to 1.

0x04

NUL

LATCH_OFF The command is rejected.

The output is set permanently

to 0.

0x41

CLOSE PULSE_ON The output is set permanently

to 1.

The command is rejected.

0x81

TRIP

PULSE_ON The output is set permanently

to 0.

The command is rejected.

The clear field (CR) is not evaluated.

The count field is always = 1.

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands