Siemens SIMATIC S7-1200 CP 1243-8 IRC Page 117 Operating Instructions Manual Download

Page: 117 / 230

Configuration

4.16 Security

CP 1243-8 IRC
Operating Instructions, 02/2018, C79000-G8976-C385-03

117

Configuration of SINEMA Remote Connect

Importing your own certificate
1.

Navigate to the parameter group "Security > Certificate manager".

Open the certificate selection with a double-click on the first free table row of the local

certificate manager.

Select the CA certificate of SINEMA RC - Server.

Then navigate to the parameter group "Security > VPN".

VPN > General
1.

Activate VPN

For the parameter "VPN connection type", select the option "Automatic OpenVPN

configuration via SINEMA Remote Connect Server" if you wish to use communication via

SINEMA Remote Connect.
If you select "Internet Key Exchange (IKE) ...", you can use communication via IPsec

tunnels.

SINEMA Remote Connect Server
Enter the address and port number of the server.

Server Verification
Here you select the authentication method of the communication module during connection

establishment.

●

CA Certificate
Under "CA certificate" select the CA certificate from SINEMA RC - Server that was

previously imported and activated in the local certificate manager.
The module generally checks the CA certificate of the server and its validity period. The

two options cannot be changed.

●

Fingerprint
When you select this authentication method, you enter the fingerprint of the server

certificate of SINEMA RC - Server.

Authentication

●

Device ID
Enter the device ID generated for the module in SINEMA RC.

●

Device password
Enter the device password of the module configured in SINEMA RC.
Max. number of characters: 127

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands