Siemens SIMATIC S7-1200 CP 1243-8 IRC Page 103 Operating Instructions Manual Download

Page: 103 / 230

Configuration

4.13 SMSC

CP 1243-8 IRC
Operating Instructions, 02/2018, C79000-G8976-C385-03

103

Enable the receipt of the time from the required time transmitter.
–

From NTP server
(only when telecontrol communication is disabled)

–

From local station
(adoption of the time from the local CPU)

–

Receive time from WAN
If the CP is connected to a classic WAN network and time-of-day synchronization is

enabled in the network, the CP automatically takes the time from the WAN network

with the settings made there. The parameter is then activated on the CP and the

parameter group is grayed out.

4.13

SMSC

If the CP (firmware V3) is intended to use the sending of SMS messages, you need to

activate the option here. Configure the number of the SMSC being used (Short Message

Service Center).
For configuring the parameters for the CP with firmware V2.1 refer to the section

Configuration of the serial interface (Page 79).

4.14

Subscriber numbers

Here you assign the subscriber numbers of the CPU and the CP.

●

Subscriber number
The subscriber number is unique for every subscriber in an ST7 network.
For the meaning of the subscriber numbers, see section ST7 (Page 61).
–

CPU subscriber number
Subscriber number of the local CPU of the station

–

CP subscriber number
Subscriber number of the CP

For the application of the master station PC, the subscriber number is configured in the

telecontrol connection: Editor "Network data" > "Telecontrol" tab
You configure WAN address of the CP in the parameter group "WAN parameters", see

section WAN parameters (networking the CP) (Page 82).

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands