Siemens SCALANCE XR-300WG Operating Instructions Manual Download Page 38 | Manualshive

Page: 38 / 100

background image

Additional notes

CAUTION

Use only approved components

If you use components and accessories that are not approved for SIMATIC NET devices or their
target systems, this may violate the requirements and regulations for safety and
electromagnetic compatibility.
Only use components approved for the SIMATIC NET devices.

NOTICE
Warming and premature aging of the IE switch due to direct sunlight

Direct sunlight can heat up the device and can lead to premature aging of the IE switch and its
cabling.

Provide suitable shade to protect the IE switch against direct sunlight.

Note

During installation and operation, keep to the installation guidelines and safety notices
described in this document and in the system manuals "Industrial Ethernet / PROFINET Industrial
Ethernet" and "Industrial Ethernet / PROFINET passive network components".

You will find information on the system manuals in the section "Introduction", under "Further
documentation".

Installation
5.1 Safety notices for installation

SCALANCE XR-300WG

38

Operating Instructions, 03/2021, C79000-G8976-C454-07

«
...
36
37
38
39
40
...
»

Summary of Contents for SCALANCE XR-300WG





































































































Reviews:

No comments

Related manuals for SCALANCE XR-300WG

Brand: IBM Pages: 164

8265 Nways ATM Switch

Brand: IBM Pages: 174

ATLONA Omega AT-OME-MS52W

Brand: Panduit Pages: 123

Atlona AT-OME-MS42

Brand: Panduit Pages: 86

SilverStorm 9000

Brand: Qlogic Pages: 50

Unified Gigabit Wireless PoE Switch 24...

Brand: 3Com Pages: 40

ProSAFE JGS516PE

Brand: NETGEAR Pages: 2

Brand: Videplus Pages: 13

Brand: HB Products Pages: 6

EG008W - Instant Gigabit Workgroup Switch

Brand: Linksys Pages: 27

Brand: Exsys Pages: 16

Brand: R&S Pages: 37

Brand: Black Box Pages: 42

Total Access 1210

Brand: ADTRAN Pages: 4

Cutler-Hammer NTV Series

Brand: Eaton Pages: 28

Brand: Watchguard Pages: 26

Brand: IP-COM Pages: 58

Brand: Key Digital Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands