Siemens SCALANCE XR-300WG Operating Instructions Manual Download Page 27

Page: 27 / 100

4.4

LED display

4.4.1

Fault LED "F"

The fault LED "F" indicates the incorrect functioning of the device.

LED color

LED status

Meaning

Off

The device is switched off or has not detected a problem.

Red

Lit

The device has detected a problem.
Using the WBM and CLI, you can set when the device sig‐
nals an error and which errors should be signaled.

4.4.2

"RM" LED

The "RM" LED indicates whether or not the device is a redundancy manager and whether or not
the ring is operating free of error.

LED color

LED status

Meaning

Off

The device is not a redundancy manager.

Green

The device is a redundancy manager.
The ring is working without problems, monitoring is activated.

Green

Flashing

The device is a redundancy manager.
An interruption has been detected on the ring and the device has
switched through.

4.4.3

LED "L"

The LED "L" shows whether the power supply is connected.

LED color

LED status

Meaning

Green

Lit

The power supply is connected.
With a redundant power supply, you can use the configuration to show
which power supply is connected.

Off

No external power supply is connected.

4.4.4

Port LEDs "P"

The port LEDs indicate the status of the ports.

RJ-45 ports
Each RJ-45 port has 2 integrated LEDs.

Description of the device

4.4 LED display

SCALANCE XR-300WG
Operating Instructions, 03/2021, C79000-G8976-C454-07

Summary of Contents for SCALANCE XR-300WG





































































































Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands

Siemens SCALANCE XR-300WG, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands