Siemens SCALANCE XR-300WG Operating Instructions Manual Download Page 97 | Manualshive

Page: 97 / 100

background image

Installation guidelines

The devices meet the requirements if you adhere to the installation and safety instructions
contained in this documentation and in the following documentation when installing and
operating the devices.

• "Industrial Ethernet / PROFINET Industrial Ethernet" System Manual (

support.industry.siemens.com/cs/ww/en/view/27069465

• "Industrial Ethernet / PROFINET - Passive Network Components" System Manual (

support.industry.siemens.com/cs/ww/en/view/84922825

• "EMC Installation Guidelines" configuration manual (

support.industry.siemens.com/cs/ww/en/view/60612658

WARNING

Personal injury and property damage can occur

The installation of expansions that are not approved for SIMATIC NET products or their target
systems may violate the requirements and regulations for safety and electromagnetic
compatibility.

Only use expansions that are approved for the system.

Note

The test was performed with a device and a connected communications partner that also meets
the requirements of the standards listed above.

When operating the device with a communications partner that does not comply with these
standards, adherence to the corresponding values cannot be guaranteed.

Approvals

SCALANCE XR-300WG
Operating Instructions, 03/2021, C79000-G8976-C454-07

97

«
...
95
96
97
98
99
...
»

Summary of Contents for SCALANCE XR-300WG





































































































Reviews:

No comments

Related manuals for SCALANCE XR-300WG

RackSwitch G8264

Brand: IBM Pages: 20

Flex System FC3171

Brand: IBM Pages: 64

Brand: 4O3A Pages: 2

Brand: Eaton Pages: 4

Brand: CZHOON Pages: 4

Brand: FS Pages: 23

Brand: Zektor Pages: 65

Brand: Conrad Pages: 8

Brand: N-Tron Pages: 20

Brand: Lindy Pages: 2

UHB-U3P1U2P3P-01

Brand: Gembird Pages: 2

StorageWorks SAN Switch Integrated/32

Brand: Compaq Pages: 104

Crocodile Tail Loop

Brand: One Control Pages: 9

Brand: PABX Pages: 46

Smart Switch 2:1

Brand: XTBA Pages: 3

USB 2.0 7-Port Hub HO97916

Brand: GE Pages: 19

Brand: Gira Pages: 2

Brand: M-E Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands