Siemens SCALANCE XR-300WG Operating Instructions Manual Download Page 91 | Manualshive

Page: 91 / 100

background image

ATEX (explosion protection directive)

WARNING

Risk of explosion in hazardous areas

When using SIMATIC NET products in hazardous area zone 2, make absolutely sure that the
associated conditions in the following document are adhered to:

"SIMATIC NET Product Information Use of subassemblies/modules in a Zone 2 Hazardous Area".

You will find this document here:
• On the data medium that ships with some products:

– Product CD / product DVD
– SIMATIC NET Manual Collection

• On the Internet pages of Siemens Industry Online Support (

support.industry.siemens.com/cs/ww/en/view/78381013

The SIMATIC NET products described in these operating instructions meet the requirements of
the EU directive 2014/34/EU "Equipment and Protective Devices for Use in Potentially Explosive
Atmospheres".

Note
Type of protection of the device

The devices are approved for various types of protection. You can find the type of protection of
your device and the ATEX certificate number on the nameplate.

Approvals

SCALANCE XR-300WG
Operating Instructions, 03/2021, C79000-G8976-C454-07

91

«
...
89
90
91
92
93
...
»

Summary of Contents for SCALANCE XR-300WG





































































































Reviews:

No comments

Related manuals for SCALANCE XR-300WG

dominion kx III

Brand: Raritan Pages: 6

Brand: Raritan Pages: 5

DOMINION KSX II

Brand: Raritan Pages: 7

Brand: Raritan Pages: 2

Brand: CoolGear Pages: 2

M800 Elite Series

Brand: 4B Pages: 12

Brand: Eaton Pages: 4

Brand: IOGear Pages: 1

Brand: Aethra Pages: 1

EdgePoint EP-S16

Brand: Ubiquiti Pages: 22

Brand: H3C Pages: 10

Premasreg 716 Series

Brand: S+S Regeltechnik Pages: 32

Brand: Samson Pages: 64

Brand: Quintech Pages: 2

Brand: N-Tron Pages: 16

Brand: Black Box Pages: 74

Brand: LEGRAND Pages: 4

Brand: Madison Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands