Siemens SCALANCE XR-300WG Operating Instructions Manual Download Page 51

Page: 51 / 100

6.2

Industrial Ethernet

6.2.1

Electrical

Note
Strain relief for the Ethernet cables

In order to avoid mechanical stress on the Ethernet cables and resulting interruption of the
contact, fasten the cables at a short distance from the connector using a cable guide or busbar.

R-45 connector technology

The attachment to Industrial Ethernet uses RJ-45 connected technology with MDI-X assignment.

Pin assignment

The following table shows the pin assignment of the RJ45 connectors.

Pin number

Assignments for ports up to

RJ45 connector

Max. 100 Mbps

Max. 1000 Mbps

Max. 10000 Mbps

Pin 1

RD+

D1+

Pin 2

RD-

D1-

Pin 3

TD+

D2+

Pin 4

n. c. (Not connec‐
ted)

D3+

Pin 5

n. c. (Not connec‐
ted)

D3-

Pin 6

TD-

D2-

Pin 7

n. c. (Not connec‐
ted)

D4+

Pin 8

n. c. (Not connec‐
ted)

D4-

Connecting up

6.2 Industrial Ethernet

SCALANCE XR-300WG
Operating Instructions, 03/2021, C79000-G8976-C454-07

Summary of Contents for SCALANCE XR-300WG





































































































Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands

Siemens SCALANCE XR-300WG, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands