Siemens SCALANCE XR-300WG Operating Instructions Manual Download Page 73

Page: 73 / 100

8.1.2

240 VAC variant

The following technical specifications apply to the 240 VAC variant of the SCALANCE XR324WG.

Technical specifications
Connection to Industrial Ethernet
Electrical connectors

Quantity

Connector

RJ45 jack

Properties

Half/full duplex, MDI‑X pinning

Transmission speed

10 / 100 Mbps

Diagnostics interface
Serial interface

Quantity

Connector

RJ-11 jack

Electrical data
Power supply

Design

Socket, 3 pin

Rated voltage

100 to 240 V AC

Voltage range

85 to 264 VAC

Frequency

50 Hz to 60 Hz

Frequency range

47 Hz to 63 Hz

Properties

Not implemented redundantly

Current consumption

At 100 VAC

200 mA

At 240 V AC

100 mA

Effective power loss

9 W

Permitted ambient conditions
Ambient temperature

During operation up to 3000 m above mean
sea level

0 ℃ to +60 ℃

During storage

-40 °C to +85 °C

During transportation

-40 °C to +85 °C

Relative humidity

During operation at 25 ℃

≤ 95% without condensation

Housing, dimensions and weight
Design

Rack

Housing material

Metal

Degree of protection

IP30

Dimensions (W x H x D)

482.6 x 43.6 x 177 mm

Weight

3300 g

Installation options

• 19" rack mounting
• DIN rail
• Wall mounting

Mean time between failure (MTBF)
MTBF (EN/IEC 61709; 40 °C) > 50 years

Technical specifications

8.1 Technical specifications of the SCALANCE XR324WG

SCALANCE XR-300WG
Operating Instructions, 03/2021, C79000-G8976-C454-07

Summary of Contents for SCALANCE XR-300WG





































































































Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands

Siemens SCALANCE XR-300WG, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands