Siemens SCALANCE XR-300WG Operating Instructions Manual Download Page 40

Page: 40 / 100

5.3

19" rack mounting

Mounting

CAUTION

Risk of injury if subjected to irregular mechanical strain

The device must be mounted in the 19" rack so that even if there is irregular mechanical strain,
no dangerous situation can result.

Figure 5-1

19" rack mounting

To install the device in a 19" rack, follow the steps below:

1. Position the device at the required location in the 19" rack.

2. Screw the two brackets to the 19" rack in each case with 2 securing screws

②

3. Connect the cables, see section "Connecting up (Page 49)".

Uninstalling

To remove the device from a 19" rack, follow the steps below:

1. Disconnect all connected cables.

2. Undo the securing screws on the mounting brackets

3. Remove the device from the 19" rack.

Installation
5.3 19" rack mounting

SCALANCE XR-300WG

Operating Instructions, 03/2021, C79000-G8976-C454-07

Summary of Contents for SCALANCE XR-300WG





































































































Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands

Siemens SCALANCE XR-300WG, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands