Siemens SCALANCE XR-300WG Operating Instructions Manual Download Page 37 | Manualshive

Page: 37 / 100

background image

WARNING

Do not remove or replace while circuit is live when a flammable or combustible atmosphere is
present.

WARNING

Explosion hazard

Do not disconnect equipment when a flammable or combustible atmosphere is present.

WARNING

EXPLOSION HAZARD

For operation the device is intended to be installed within an enclosure/control cabinet. The
inner temperature of the enclosure/control cabinet corresponds to the ambient temperature of
the device. Use installation wiring connections with admitted maximum operating
temperature of at least 30 °C higher than maximum ambient temperature.

Safety notices when using the device as industrial control equipment according to UL

61010-2-201
If you use the device under UL 61010-2-201 conditions you must also keep to the following
safety notices in addition to the general safety notices for protection against explosion:

WARNING

Open equipment

The devices are "open equipment" according to the standard IEC 61010-2-201 or UL
61010-2-201 / CSA C22.2 No. 61010-2-201. To fulfill requirements for safe operation with
regard to mechanical stability, flame retardation, stability, and protection against contact, the
following alternative types of installation are specified:
• Installation in a suitable cabinet.
• Installation in a suitable enclosure.
• Installation in a suitably equipped, enclosed control room.

WARNING

If the cable or housing socket exceeds 70 °C or the branching point of the cables exceeds 60 °C,
special precautions must be taken. If the equipment is operated in an air ambient in excess of
40 °C, only use cables with admitted maximum operating temperature of at least 80 ℃.

Installation

5.1 Safety notices for installation

SCALANCE XR-300WG
Operating Instructions, 03/2021, C79000-G8976-C454-07

37

«
...
35
36
37
38
39
...
»

Summary of Contents for SCALANCE XR-300WG





































































































Reviews:

No comments

Related manuals for SCALANCE XR-300WG

SmartPro DGS-1500-20

Brand: D-Link Pages: 113

xStack DGS-3120 Series

Brand: D-Link Pages: 1150

SUPERSTACK 3 3226

Brand: 3Com Pages: 5

Brand: 3Com Pages: 139

CoreBuilder 7000

Brand: 3Com Pages: 150

CoreBuilder 7000

Brand: 3Com Pages: 264

Brand: 3Com Pages: 574

Brand: 3Com Pages: 333

SUPERSTACK 3 3226

Brand: 3Com Pages: 70

OfficeConnect 3C16790C

Brand: 3Com Pages: 18

Brand: 3Com Pages: 1314

SuperStack II Switch 1100

Brand: 3Com Pages: 62

Brand: eao Pages: 2

Brand: eao Pages: 2

Brand: Panio Pages: 5

Brand: Attwood Pages: 2

Draco major K474-U8/C8

Brand: Ihse Pages: 167

Brand: steute Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands