Siemens SCALANCE XR-300WG Operating Instructions Manual Download Page 96

Page: 96 / 100

Applied standards:

• AS/NZS CISPR11 (Industrial, scientific and medical equipment - Radio-frequency disturbance

characteristics - Limits and methods of measurement).

• EN 61000-6-4 Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission

standard for industrial environments

You will find the current versions of the standards in the currently valid RCM SDoCs (Self-
Declaration of Conformity).

MSIP

요구사항

‑ For Korea only

급

기기

(

업무용

방송통신기자재

)

이

기기는

업무용

급

)

전자파

적합기기로서

판매자

또는

사용자는

이

점을

주의하시기

바라며

가정

외의

지역에서

사용하는것을

목적으로

합니다

Marking for the customs union

EAC (Eurasian Conformity)

Eurasian Economic Union of Russia, Belarus, Armenia, Kazakhstan and Kyrgyzstan

Declaration of conformity according to the technical regulations of the customs union (TR ZU)

FDA and IEC marking

The following devices meet the FDA and IEC requirements listed below:

Device

CLASS 1 LASER Product

SCALANCE XR324WG

SCALANCE XR328‑4C WG

(*)

* In modular devices, you can find the marking on the plug-in transceiver used or in the relevant operating
instructions.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.

Approvals

SCALANCE XR-300WG

Operating Instructions, 03/2021, C79000-G8976-C454-07

Summary of Contents for SCALANCE XR-300WG





































































































Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands

Siemens SCALANCE XR-300WG, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XR-300WG

Reviews:

Related manuals for SCALANCE XR-300WG

Brands by name

Popular brands