manualshive.com logo in svg

Siemens interranger DPS300, Instructional Manual, Page: 83 / 111

Share
Download
Siemens interranger DPS300 Instructional Manual Download Page 83

 

7ML19981BC01 

83

 InterRanger 

DPS300

 

Advanced Echo Processing (P810 to P853) 

Note: 

The following Echo Processing parameters are intended for use by authorized 
Siemens Service personnel or Industrial Instrumentation Technicians familiar with 
Siemens ultrasonic echo processing techniques.  

Anatomy of an Echo Profile 

The relevant parts of an echo profile are listed here. These are visible in either 
Dolphin Plus or an oscilloscope.  

 

P810  Scope Displays  

Use this feature to monitor the results of Echo Processing parameter alterations.  

Connect an oscilloscope to Display Board TP4, TP5, and TP6 (GND, SCOPE and 
SYNC).  

Observe any combination of the following Scope Displays:  

DISPLAY 

    DISPLAY 

SYMBOL 

 

 

 

 

 

 

 

 P      C     n      u  

Echo Profile  

TVT Curve  

Echo Marker  

Echo Lock Window  

echo profile 

TVT curve 

selected echo 

echo lock window 

echo marker

Summary of Contents for interranger DPS300
















































































































Reviews:

No comments