manualshive.com logo in svg

Siemens interranger DPS300, Instructional Manual, Page: 79 / 111

Share
Download
Siemens interranger DPS300 Instructional Manual Download Page 79

 

7ML19981BC01 

79

 InterRanger 

DPS300

 

P731  (G)  Auxiliary Reading Key  

Use this feature to enable a specific Parameter Value to be monitored in the RUN 
mode.  

Enter the Parameter Number whose value is to be displayed in the Auxiliary 
Reading field when 

 is pressed in the RUN mode.  

(See OPERATION Keypad for RUN mode Auxiliary Reading selection.)  

Values: 

000 to 999  (preset to Material Measurement, P921)  

P732  (G)  Display Delay  

Use this feature if the Point Number display scrolls too quickly in the RUN mode.  

Enter the delay (in seconds) before the display advances to the next Point 
Number.  

(Point Number display scrolling is independent from transducer scanning.)  

Values: 

0.5 to 10 (preset to 1.5 seconds)  

P733  (G)  Scroll Access  

Use this feature to select the programming mode parameter scroll access option 
desired.  

Select: 

“off”  

to scroll access all operator accessible parameters.  

“smart”  

to scroll access Quick Start, previously altered, and tagged 
parameters.  

“tagged”  

to scroll access operator tagged parameters only.  

Any accessed parameter may be 

tagged

 or 

untagged

 by pressing 

 

. 

 

is displayed when a previously tagged or altered parameter is accessed.  

Values: 

0 = off  
1 = smart (preset)  
2 = tagged  

Peripheral Communication Support Parameters (P740 to P772) 

P740  Peripheral Communications  

Use this feature to select the DPS300 to communication message format.  

Select: 

“off” 

if the communication port is not used, to increase the DPS300 
processing speed.  

Summary of Contents for interranger DPS300
















































































































Reviews:

No comments