manualshive.com logo in svg

Siemens interranger DPS300, Instructional Manual, Page: 49 / 111

Share
Download
Siemens interranger DPS300 Instructional Manual Download Page 49

 

7ML19981BC01 

49

 InterRanger 

DPS300

 

 OPERATION   

With Quick Start parameter alteration complete, the DPS300 may be put into 
operation. (If APPLICATION or ENHANCEMENT PARAMETERS are altered, 
OPERATION is altered accordingly from that indicated).  

Display  

In the RUN mode, the following values and indicators may be observed.  
Note that many indicators are specific to certain operating conditions and 
therefore, 

all indicators are not displayed at any given time. 

 

 

Transducer 

the current display pertains to a transducer measurement.

  

Point Number 

the Point Number (1 or 2) the current display pertains to. 

 

Reading 

displays the level, space, or distance (flashes error messages, 
if any).

 

Percent 

the Reading is in percent.

 

High Alarm 

indicates sludge level has risen above 80% (and not yet fallen 
below 75%).

 

Low Alarm 

indicates sludge level has fallen below 20% (and not yet risen 
above 25%).

 

Filling Indicator 

indicates the sludge level is rising.

 

Emptying Indicator 

indicates the sludge level is lowering.

 

Bar Graph 

indicates the absolute (always a positive value) sludge level 
from 0 to 100%.

 

Data Out 

indicates the DPS300 is transmitting data to the 
Communications terminals. 

 

Scanning Indicators 

indicate the Point Number scanned (independent from the 
Point Number display).

 

Auxiliary Reading 

as selected by the keypad (terminal numbers if transducer or 
TS-3 is wired wrong).

 

Relay Number 

indicates the relays programmed for operation. 

 

Relay Status 

indicates the relay is de-energized (alarm is activated).

 

Normal Operation 

indicates operating conditions are good and the Reading is 
reliable.

 

Failsafe Operation 

indicates operating conditions are poor and the Reading may 
be incorrect.

 

transducer

point 

number 

reading 

units 

high alarm

indicator 

filling /

emptying

indicator

bar graph

low alarm

indicator 

data out

indicator 

scanning 

indicators 

auxiliary

reading 

number 

fail-safe 

operation 

normal 

operation 

status 

relay:

Summary of Contents for interranger DPS300
















































































































Reviews:

No comments