manualshive.com logo in svg

Siemens interranger DPS300, Instructional Manual, Page: 15 / 111

Share
Download
Siemens interranger DPS300 Instructional Manual Download Page 15

 

7ML19981BC01 

15

 InterRanger 

DPS300

 

As a System 

As a system, the DPS300 is made up of: 

minimum

 

maximum

 

one DPS300 

one DPS300 

one XCT-12 transducer 

two XCT-12 transducers 

 

one Skimmer Guard per transducer 

 

one Mounting Assembly per transducer 

 one 

SmartLinx 

communications 

module 

 

 

DPS300 System Integration 

•

  Assemble the transducer to the Siemens Skimmer Guard if provided. Otherwise 

install directly to your conduit with a ¾” to 1” NPT or BSP reducer. 

Refer to the Skimmer Guard section for dimension and assembly details. Refer to 
the XCT-12 manual for connection and wiring details only. 

•

  Assemble the Siemens Mounting Assembly, if provided, to the handrail. And, 

mount the transducer (with Skimmer Guard if provided) to the Mounting Assembly. 
Otherwise mount the transducer assembly in a secure fashion. 

Refer to the Mounting Assembly section for dimensions and assembly details. 

•

  Install the DPS300 and program the unit for your specific application. 

Refer to the Application and Parameters sections of this manual. 

DPS300 

Siemens Mounting Assembly 

Mounts the transducer to 
handrails along the clarifier 
walkway or bridge. 

Optional Siemens 

Skimmer Guard

The Skimmer Guard

protects the transducer by 

allowing it to ride over a

passing skimmer.

customer

conduit

Siemens  XCT-12 

The ultrasonic transducer used with the DPS300. If 
the DPS300 is programmed to monitor two clarifiers, 
then two transducers are required. 

Note: 

Operation of the transducer requires that the face be 
immersed 3 to 6 cm into the clarifier wastewater.

 

DPS300

mounting

plate

Summary of Contents for interranger DPS300
















































































































Reviews:

No comments