manualshive.com logo in svg

Siemens interranger DPS300, Instructional Manual, Page: 42 / 111

Share
Download
Siemens interranger DPS300 Instructional Manual Download Page 42

InterRanger DPS300 

42

 7ML19981BC01

 

 PROGRAMMING   

Operator programmable features are identified by a Point Number and Parameter 
Number. The Point Number refers to the Transducer (clarifier) Number, Relay 
Number, or mA Output Number as identified by the Point Type indicators. 
Parameter Numbers have a preset Parameter Value for each Point Number.  

Programming is accomplished by altering the preset Parameter Values as 
required to obtain the RUN mode operation desired. All operator programmable 
features are defined in the Quick Start Parameters, Application Parameters, and 
Enhancement Parameters sections of this instruction manual.  

Display  

In the program mode, the Point Type, Point Number, Parameter Number, and 
Parameter Value (as well as a variety of other programming information) may be 
viewed.  

Note that many indicators are specific to certain programming conditions and 
therefore, not all indicators are displayed at any given time.  

 

 

Parameter Number

  the programmable feature the Parameter Value pertains to. 

Point Type 

the Point Number refers to a Transducer, Relay, mA Output, or 
TS-3. 

Point Number 

the Transducer, Relay, mA Output or TS-3 # the Parameter 
Value pertains to.  

Parameter Value

 

the current value of the Parameter Number for the Point 
Number displayed.  

Percent 

indicates the Parameter Value is displayed in percent. 

Invalid Entry 

indicates the value entered is questionable (are you sure?).  

Auxiliary Function

 

indicates Auxiliary Function access (applies to only some 
Parameter Numbers).  

Scroll Access Tag

 

indicates the Parameter Value may be scroll accessed.  

Program Mode 

indicates the program mode is accessed.  

point 

type 

point 

number 

parameter 

value 

units 

auxiliary 

function 

scroll 

access tag 

invalid

entry 

parameter

number 

program 

mode 

relay in 
service 

transducer 

relay 

analog output 

TS-3 

index 

Summary of Contents for interranger DPS300
















































































































Reviews:

No comments