Siemens interranger DPS300 Instructional Manual Download Page 6

Page: 6 / 111

InterRanger DPS300

7ML19981BC01

Communications:

SmartLinx ® compatible

(see Options)

RS-232 / 485 port

Dolphin compatible

proprietary bipolar current loop for BIC-2 communication

Enclosure:

Type 4 / NEMA 4 / IP65

285 mm W x 209 mm H x 92 mm D (11.2” W x 8.2” H x 3.6” D)

polycarbonate

Weight:

2.7 kg (6 lb)

Approvals:

, CSA

NRTL/C

*EMC performance available upon request

Programmer

Power:

may be supplied with either:

3 V Lithium (non-replaceable)

9 V (ANSI/NEDA 1604, PP3 or equivalent)

Ambient Temperature:

-20 to 50°C (-5 to 122°F)

Keypad:

20 keys with tactile feedback

Interface:

non-invasive, digital, infra-red

Enclosure:

general purpose

67 mm W x 100 mm H x 25 mm D (2.6” W x 4” H x 1” D)

ABS plastic

Weight:

150 g (0.3 lb)

Transducer

Model:

Echomax

XCT-12

Beam angle:

30°

(in water)

Range:

1 to 30m (3.3 to 99’)

Refer to the associated instruction manual for wiring only (not installation).

Summary of Contents for interranger DPS300
















































































































Search results

Summary of Contents for interranger DPS300

Reviews:

Siemens interranger DPS300, Instructional Manual, Page: 6 / 111

Search results

Summary of Contents for interranger DPS300

Reviews: