Siemens FCT010/DSL Operating Instructions Manual Download Page 91

Page: 91 / 180

9.6.2

Ex-approved products

Note
Repair of Ex-approved products

It is the customer's responsibility that repair of Ex-approved products fulfill national
requirements.

9.6.3

Replaceable components

This table gives an overview of which components can be replaced.

Component

Order number

Photo

Replacable in Ex
devices

Hot swappable

SITRANS FC
Bag of loose parts for sensor
Contents:
Screws, O-rings, cable clamp
parts

A5E03549324

Yes

Observe hazard‐

ous area access

protocol

SITRANS FCT010
Blind lid in painted aluminum
small (∅85 mm)

A5E03549295

Yes

Observe hazard‐

ous area access

protocol

Yes

Observe hazardous

area access proto‐

col

Sensor housing with cable en‐
tries in metric tread

A5E03549313

Sensor housing with cable en‐
tries in NPT tread

A5E03906080

SITRANS FCS400
M12 option for sensor housing

A5E03906095

Frontend cassette
Spare part frontend cassette
for FCT010/DSL
From firmware 4.0

A5E41526286

Service and maintenance

9.6 Spare parts/Accessories

SITRANS MASS 2100 & FC300 (FCT010/DSL)
Operating Instructions, 06/2020, A5E39788682-AB

Summary of Contents for FCT010/DSL





















































































































































































Search results

Summary of Contents for FCT010/DSL

Reviews:

Siemens FCT010/DSL, Operating Instructions Manual, Page: 91 / 180

Search results

Summary of Contents for FCT010/DSL

Reviews: