manualshive.com logo in svg

Siemens FCT010/DSL, Operating Instructions Manual, Page: 69 / 180

Share
Download
Siemens FCT010/DSL Operating Instructions Manual Download Page 69

Operating FCT010

7

7.1

Remote operation

For information on Modbus addresses, registers  and function codes see appendix Modbus 
communication FCT010 (Page 151).

7.1.1

Overview of device configuration software

There are currently two competing technologies for configuring field devices:

• Electronic Device Description Language (EDDL)-based software

• Field Device Tool / Device Type Manager (FDT/DTM)-based software

From a practical point of view, both EDDL and FDT/DTM solutions do the same thing: provide a 
way of reading and writing configuration parameters to field devices and viewing advanced 
diagnostics.

Note
• SIMATIC PDM (an EDDL-based software) configures a field device using the Electronic Device 

Description (EDD) for that device.

• PACTware and Fieldcare (FDT-based software) use the DTM for that field device.

In addition, there is a new standard called Field Device Integration (FDI) which is a merger of 
these two technologies. Many of the major vendors have stated that their configuration 
software will evolve into being an FDI host. At the time this manual was written, Siemens had 
announced that SIMATIC PDM will become a FDI host system in the near future.

7.1.2

SIMATIC PDM

7.1.2.1

Overview SIMATIC PDM

SIMATIC PDM (Process Device Manager) is a general-purpose, manufacturer-independent tool 
for the configuration, parameter assignment, commissioning, diagnostics and maintenance of 
intelligent field devices and field components. Follow-up installations and additional 
information on SIMATIC PDM are available on the Internet at SIMATIC PDM (

www.siemens.com/

simatic-pdm

).

SIMATIC PDM monitors the process values, alarms and status signals of the device. It allows you 
to display, compare, adjust, verify, and simulate process device data; also to set schedules for 
calibration and maintenance.

For information on, for example, how to install and integrate devices, commission the software, 
see Operating Manual 'Help for SIMATIC PDM'. The manual is delivered with SIMATIC PDM 

SITRANS MASS 2100 & FC300 (FCT010/DSL)
Operating Instructions, 06/2020, A5E39788682-AB

69

Summary of Contents for FCT010/DSL





















































































































































































Reviews:

No comments