Sharp SF-DM11 Service Manual Download Page 42

Page: 42 / 141

(2)

If the copy image at the leading edge was distorted, enter value
which will move the original toward the glass side.
9, 10, 11...

(3)

If the original overrode the stopper, enter value which will move
the original toward the glass side.
9, 10, 11, 12 ...

•

After selecting test command 53 , enter a selected set value
between 0 and 15 using the copier keys.

(3) SF-S53

Stopper

Glass

Original

Stopper

Glass

Original

★

Set to between 0 and 15 as dictated by the copier's performance.
The factory setting is "8".

(a)

(b)

(a) One-sided mode
(b) Two-sided mode

For SF-A17, only (a) is possible.

Included parts

Caster screws
(M4 x 50): 8

Sorter mounting plate screws
(M4 x 12): 2

Rail mounting plate screws
(M4 x 14): 2

Rail screws A
(M4 x 6): 2

Rail screws B
(M4 x 6): 1

Bracket screws
(M4 x 10): 2

Caster spacers: 4

Rail: 1

Sorter mounting plate: 1

Rail mounting plate: 1

Green label: 1

Support guide: 1

Stapling location label A: 1

Stapling location label D: 1

Sorter protection mat: 1

5 – 13

Summary of Contents for SF-DM11














































































































































Search results

Summary of Contents for SF-DM11

Reviews:

Related manuals for SF-DM11

Brands by name

Popular brands

Sharp SF-DM11, Service Manual

Search results

Summary of Contents for SF-DM11

Reviews:

Related manuals for SF-DM11

Brands by name

Popular brands