Sharp SF-DM11 Service Manual Download Page 56

Page: 56 / 141

12. Connect the sorter connector.

Remove the sorter connector cover securing screw which is mounted
to the rear cabinet panel of the copier and remove the sorter connec-
tor cover.

Connect the sorter connector to the connector on the copier and
secure it using the sorter connector securing screw.

Plug the copier into a grounded outlet and turn the
power switch on.

Then, follow the procedure below.

13. Set the mode.

•

Operate the copier keys to set the mode.

The above key operation will display the currently set mode.

•

When only the SF-S18 is to be set, immediately after the above
key operation, operate the keys as follows:

•

If the mode is to be set in combination with other options, use the
table shown below to add up the total of the setting values for all
the peripheral devices to be set, and set that total value.

For example, if the SF-S18 and RADF are to be set, the total
setting value is 1 + 10 = 11.

Operate the keys as follows:

RADF

Stand/paper drawer

SF-S18

ADF

(6) SF-S15 (20-Bin Sorter)

Unplug the copier and follow the procedure below.

1. Install the support guide.

Hook the pawls (two locations) of the support guide to the inside of
the copier paper exit end to install the guide as shown in Fig.

Sorter connector cover

Securing screw

Sorter connector

SF-S15

Parts list

Sorter seat

Support guide

Sorter seat mounting
fixture (1 pc.)

Sorter seat mounting
screws A (2 pcs.)

Sorter seat mounting
screws B (1 pc.)

Bracket mounting
screws B (2 pcs.)

Support guide

5 – 27

Summary of Contents for SF-DM11














































































































































Search results

Summary of Contents for SF-DM11

Reviews:

Related manuals for SF-DM11

Brands by name

Popular brands

Sharp SF-DM11, Service Manual

Search results

Summary of Contents for SF-DM11

Reviews:

Related manuals for SF-DM11

Brands by name

Popular brands