Sharp SF-DM11 Service Manual Download Page 49

Page: 49 / 141

•

Attach the support plate to the sorter mounting angle R and the
connecting plate, and fix it with four fixing screws.

Remove the rear cabinet panel from the sorter.
Loosen the 4 screws securing the rear cabinet panel to the sorter,
then remove the rear cabinet panel.

g. Mount the paper guide.

Insert the paper guide harness through the hole, and use the 2
mounting screws to attach the paper guide.

Connect the 3-pin connector of the paper guide harness to the
3-pin connector of the sorter control base.

h. Install the rear cabinet panel to the sorter.

Tighten the 4 mounting screws to install the rear cabinet panel.

Mount the sorter onto the copier.

•

Fit the guide plate on the sorter body into the guides on the
front and rear sorter mounting angles.

Attach the handle to the sorter.
Attach the handle mounting plates F and R to the sorter shaft as
shown in the figure, and fix it with two fixing screws.
Then attach the handle to the handle mounting plates F and R
and fix it with two fixing screws.

Mounting
screws

Support plate

Sorter mounting angle, rear

Mounting
screws

Rear cabinet panel

Mounting
screws

Rear cabinet panel

Mounting
screws

Rear cabinet panel

Mounting
screws

Guide plates

Handle support plate, front

Handle

Mounting
screw

Handle support
plate, rear

Shaft

Mounting screw

5 – 20

Summary of Contents for SF-DM11














































































































































Search results

Summary of Contents for SF-DM11

Reviews:

Related manuals for SF-DM11

Brands by name

Popular brands

Sharp SF-DM11, Service Manual

Search results

Summary of Contents for SF-DM11

Reviews:

Related manuals for SF-DM11

Brands by name

Popular brands