Sharp SF-DM11 Service Manual Download Page 120 | Manualshive

Page: 120 / 141

background image

Main code

Sub code

Description

Ref. Page

03

02

This is the test command used to test the sensors in the sorter.
On/off state of sensors can be manually tested.
When the sensor turns on, the display reverses.

Paper entry sense (non-sort)

PES/SPID

Indexer upper limit sense

IULS/—

Sorter set sense

SJS/JSW

Paper entry sense (sort)

—/SPPD

Indexer lower limit sense

ILLS/—

Top cover open/close sense

UCSW/—

Paper out sense

PWB-S/—

Indexer (bin) home sense

IHS/BHPS

Blower cover open/close sense

FCSW/—

Bin paper sense

—/BPED

Indexer (bin) position sensor

IPS/LCHPS

Staple cover open/close sense

—/SCSW

Staple position paper sense

—/SPED

Guide bar home position sense

—/SGHPS

Staple unit home position

sense

—/SCS

Staple unit position sense

—/SSD

Staple operation home position

sesnse

—/SHPS

Stapler needle sense

—/SED

Note: The signal names are given in the order of S15/S53.

Reverse display: paper found/door opened/ON
Normal display: no paper found/door closed/OFF

03

Used to test the components of the sorter (individual load check).
Transport motor rotation

04

Indexer motor rotation (returns to the home position at first, then stops at each bin location Bin 1 to Bin
21, moving up and down. Sorter bin moving.

05

Fan motor rotation in the case of SF-S15 only

06

Gate solenoid ON

07

Offset solenoid (in the case of SF-S53)

08

Stapler motor rotation (the paper is stapled once when there is a paper in the stapler tray). (SF-S53
only)

09

Paper holder solenoid operation check (SF-S53 only)

10

Guide motor operation check

04

02

This is the test command used to test sensors in the desk. On/off state of the sensors can be manually
tested.
When a sensor turns on, the display reverses.

Sensing paper fed from the

upper cassette

DPOD1

Upper cassette lift upper limit

sensor

DLUD1

Sensing paper presence on

the upper cassette

DPE1

Sensing paper fed from the

middle cassette

DPOD2

Middle cassette lift upper limit

sensor

DLUS2

Sensing paper presence on

the middle cassette

DPE2

Sensing paper fed from the

bottom cassette

DPOD3

Bottom cassette lift upper limit

sensor

DLUD3

Sensing paper presence on

the bottom cassette

DPE3

Sensing door close/open

DDOP

—

—

Reverse display: paper found/door opened/ON
Normal display: no paper found/door closed/OFF

03

Used to test the on/off state of the first cassette size switch of the desk.
When the switch turns on, the display reverses.
(Cassette size board)
Switch positions when viewed from the front frame

04

Used to test the on/off state of the second cassette size switch of the desk. Function is identical to the
test command 04-03.

05

Used to test the on/off state of the third cassette size switch of the desk. Function is identical to the test
command 04-03.

CSSW4

CSSW3

CSSW2

CSSW1

1

5

CN

Paper exit side

Paper entry side

8 – 5

«
...
118
119
120
121
122
...
»

Summary of Contents for SF-DM11














































































































































Reviews:

No comments

Related manuals for SF-DM11

Brand: Xerox Pages: 2

Brand: Xerox Pages: 103

Brand: Xerox Pages: 2

DocuPrint 4850 NPS

Brand: Xerox Pages: 68

Brand: Xerox Pages: 28

DocuColor 5000AP

Brand: Xerox Pages: 5

Document WorkCentre 450c

Brand: Xerox Pages: 214

Brand: Xerox Pages: 68

Brand: Xerox Pages: 2

Brand: Xerox Pages: 170

Phaser 5500 series

Brand: Xerox Pages: 2

Brand: Xerox Pages: 238

Brand: Xerox Pages: 24

Brand: Xerox Pages: 18

Brand: Xerox Pages: 18

Brand: Xerox Pages: 2

Brand: Xerox Pages: 158

Brand: FujiFilm Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands